ADC AD-320 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 60

background image

112144 - 46

www.adclaundry.com

43

SECTION VII

ROUTINE MAINTENANCE

A. CLEANING

A program and/or schedule

should be

established for periodic inspection, cleaning, and removal of lint from various

areas of the dryer, as well as throughout the ductwork system. The frequency of cleaning can best be determined
from experience at each location. Maximum operating efficiency is dependent upon proper air circulation. The
accumulation of lint can restrict this airflow. If the guidelines in this section are met, an

ADC

dryer will provide

many years of efficient, trouble free, and most importantly, safe operation.

WARNING: LINT FROM MOST FABRICS IS HIGHLY COMBUSTIBLE. THE

ACCUMULATION OF LINT CAN CREATE A POTENTIAL FIRE HAZARD.

WARNING: KEEP DRYER AREA CLEAR AND FREE FROM COMBUSTIBLE

MATERIALS, GASOLINE, AND OTHER FLAMMABLE VAPORS AND
LIQUIDS.

NOTE:

Suggested time intervals shown are for average usage, which is considered six (6) to eight (8)
operational (running) hours per day.

IMPORTANT:

Dryer produces combustible lint and

must be

exhausted to the outdoors. Every 6

months, inspect the exhaust ducting and remove any lint build up.

SUGGESTED CLEANING SCHEDULE

DAILY (beginning of each work shift)

Clean lint from lint drawer/screen.

Inspect lint screen and replace if torn.

WEEKLY

Clean lint accumulation from around microprocessor temperature sensor probes and sensor bracket assemblies.

WARNING: TO AVOID HAZARD OF ELECTRICAL SHOCK, DISCONTINUE

ELECTRICAL POWER SUPPLY TO THE DRYER.

STEAM DRYERS

Clean steam coil fins. Suggest using compressed air and vacuum cleaner with brush attachment.

«
...
45
46
47
48
49
...
»

Содержание AD-320





























































Отзывы:

Нет отзывов

Похожие инструкции для AD-320

Бренд: Nelsen Corporation Страницы: 16

Бренд: National Instruments Страницы: 34

Бренд: Canon Страницы: 2

Бренд: Parker Страницы: 30

Бренд: VAT Страницы: 22

Бренд: Galcon Страницы: 32

Бренд: D+H Страницы: 14

Бренд: eclisse Страницы: 40

Бренд: IDK Страницы: 96

Бренд: M-system Страницы: 103

Бренд: M-system Страницы: 18

Бренд: M-system Страницы: 7

Бренд: OJ Electronics Страницы: 8

Бренд: OJ Electronics Страницы: 112

Бренд: OJ Страницы: 17

Бренд: National Instruments Страницы: 72

Бренд: National Instruments Страницы: 41

MAGNUM ALERT 3000 FIRE ALARM

Бренд: NAPCO Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды