ADC AD-320 Скачать руководство пользователя страница 50

Страница: 50 / 60

American Dryer Corp.

112144 - 46

C. Basket (tumbler) does not turn, but motor and Dual Microprocessor Controller (DMC) computer

motor light emitting diode (L.E.D.) dot and motor output L.E.D. indicators are on...

1. Loose basket (tumbler) belt (check tension/adjustment).

2. Basket (tumbler) belt jumped off of motor or idler shaft.

3. Broken basket (tumbler) belt.

D. The dryer will not stop, even with no cycle (L.E.D. display reads “FILL”) in progress...

1. Failed motor contactor/relay.

E. The dryer operates for a few minutes, and with the DMC computer motor L.E.D. indicator dot on

the motor stops, and then after a period of time restarts on its own...

1. Motor is overheating and tripping out on its internal overload...

a. Motor air vents clogged with lint.

b. Low voltage to motor.

The dryer operates for a few minutes and then stops...DMC computer L.E.D. display continues to
read cycle in progress, indicator dots are off and dryer can be restarted by pressing selection
key...

1. Intermittent connection in main door/lint drawer circuit...

a. Main door switch or lint drawer switch out of proper adjustment.

b. Loose connection in main door switch or lint drawer switch wiring.

c. Failed main door switch or lint drawer switch.

G. The dryer does not start, and the DMC computer L.E.D. display reads “door”...

1. DMC “door” input L.E.D. is off...

a. Main door and/or lint drawer is not properly closed.

b. Failed main door switch.

c. Failed lint drawer switch.

d. Open circuit (broken wire and/or termination) in main door switch circuit wiring or lint drawer switch

circuit wiring.

e. Failed 24 VAC step down transformer.

2. DMC “door” input L.E.D. is on...

a. Failed DMC computer.

H. The dryer does not start (COIN MODELS ONLY)...coin(s) inserted and the L.E.D. display

continues to read “FILL” and/or “Amount To Start” (does not read “PUSH”)...

1. Coin acceptor is not adjusted properly (housing is not flush with panel) or is dirty with lint.

2. Failed coin acceptor optic switch.

Содержание AD-320





























































Результаты поиска

Содержание AD-320

Отзывы:

Похожие инструкции для AD-320

Бренды по названию

Популярные бренды

ADC AD-320, Руководство по установке

Результаты поиска

Содержание AD-320

Отзывы:

Похожие инструкции для AD-320

Бренды по названию

Популярные бренды