ABB Relion Скачать руководство пользователя страница 656 | Manualshive

Страница: 656 / 778

background image

16.6.4

Signals

Table 472:

GOOSEINTRCV Input signals

Name

Type

Default

Description

BLOCK

BOOLEAN

0

Block of function

Table 473:

GOOSEINTRCV Output signals

Name

Type

Description

INTOUT

INTEGER

Integer output

DATAVALID

BOOLEAN

Data valid for integer output

COMMVALID

BOOLEAN

Communication valid for integer output

TEST

BOOLEAN

Test output

16.6.5

Settings

Table 474:

GOOSEINTRCV Non group settings (basic)

Name

Values (Range)

Unit

Step

Default

Description

Operation

Disabled

Enabled

-

-

Disabled

Operation Off/On

16.6.6

Operation principle

The DATAVALID output will be HIGH if the incoming message is with valid data.

The COMMVALID output will become LOW when the sending IED is under total failure
condition and the GOOSE transmission from the sending IED does not happen.

The TEST output will go HIGH if the sending IED is in test mode.

The input of this GOOSE block must be linked in SMT by means of a cross
to receive the integer values.

The implementation for IEC61850 quality data handling is restricted to a
simple level. If quality data validity is GOOD then the DATAVALID
output will be HIGH. If quality data validity is INVALID,
QUESTIONABLE, OVERFLOW, FAILURE or OLD DATA then the
DATAVALID output will be LOW.

Section 16

1MRK 502 048-UUS A

Station communication

650

Technical manual

«
...
654
655
656
657
658
...
»

Содержание Relion











































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Relion

Бренд: DoorHan Страницы: 2

Бренд: OBO Bettermann Страницы: 4

Бренд: CATU Страницы: 2

Бренд: ZIEHL Страницы: 48

Бренд: RCA Страницы: 64

Бренд: 3M Страницы: 138

Бренд: ABB Страницы: 91

Бренд: Magnavox Страницы: 54

Бренд: AISENLIN Страницы: 3

Бренд: Sony Страницы: 138

Jetstream Series

Бренд: TP-Link Страницы: 2

Бренд: MULTISPAN Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды