ABB Relion Скачать руководство пользователя страница 331 | Manualshive

Страница: 331 / 778

background image

10.2.7

Operation principle

Overfrequency protection SAPTOF (81) is used to detect high power system frequency.
SAPTOF (81) has a settable definite time delay. If the frequency remains above the set
value for a time period greater than the set time delay the TRIP signal is issued. To avoid
an unwanted TRIP due to uncertain frequency measurement at low voltage magnitude, a
voltage controlled blocking of the function is available from the preprocessing function,
that is, if the voltage is lower than the set blocking voltage in the preprocessing function,
the function is blocked and no PICKUP or TRIP signal is issued.

10.2.7.1

Measurement principle

The frequency measuring element continuously measures the frequency of the positive
sequence voltage and compares it to the setting

PUFrequency

. The frequency signal is

filtered to avoid transients due to switchings and faults in the power system. If the voltage
magnitude decreases below the setting

MinValFreqMeas

in the SMAI preprocessing

function, which is discussed in the Basic IED Functions chapter and is set as a percentage
of a global base voltage parameter

VBase

, SAPTOF (81) is blocked and the output

BLKDMAGN is issued. All voltage settings are made in percent of the global parameter

VBase

. To avoid oscillations of the output PICKUP signal, a hysteresis has been included.

PICKUP

PICKUP

TRIP

Pickup

&

Trip

Output

Logic

Definite Time Delay

TimeDlyOperate

BLOCK

ANSI09000033-1-en.vsd

Frequency

Comparator

f > PUFrequency

TRIP

BLKDMAGN

BLOCK

OR

freqNotValid

ANSI09000033 V1 EN

Figure 152:

Schematic design of overfrequency protection SAPTOF (81)

1MRK 502 048-UUS A

Section 10

Frequency protection

325

Technical manual

«
...
329
330
331
332
333
...
»

Содержание Relion











































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Relion

Бренд: Samlex Europe Страницы: 19

Screen Protector for Fitbit Sense 2

Бренд: Wasserstein Страницы: 8

Бренд: Marantz Страницы: 8

Бренд: Dräger Страницы: 28

Бренд: Fiessler Страницы: 46

Бренд: 3M Страницы: 26

Бренд: Faster Страницы: 68

Бренд: Magnavox Страницы: 60

Бренд: Samsung Страницы: 146

Бренд: Kenwood Страницы: 148

Pro-Anchor PA-132-EV

Бренд: Omni cubed Страницы: 13

HD-ILA HD-52G786

Бренд: JVC Страницы: 104

PYROPLUG MagicBox

Бренд: OBO Bettermann Страницы: 24

DRYSUIT Neoprene

Бренд: Uwatec Страницы: 172

Бренд: Tescom Страницы: 6

WORKMASTER TASKLITE+

Бренд: Respirex Страницы: 16

WORKMASTER DIELECTRIC HV3

Бренд: Respirex Страницы: 16

Бренд: Arcteq Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды