ABB Relion Скачать руководство пользователя страница 687 | Manualshive

Страница: 687 / 778

background image

17.4.5

Settings

Table 504:

TESTMODE Non group settings (basic)

Name

Values (Range)

Unit

Step

Default

Description

TestMode

Disabled

Enabled

-

-

Disabled

Test mode in operation (Enabled) or not

(Disabled)

EventDisable

Disabled

Enabled

-

-

Disabled

Event disable during testmode

CmdTestBit

Disabled

Enabled

-

-

Disabled

Command bit for test required or not during

testmode

17.4.6

Operation principle

Put the IED into test mode to test functions in the IED. Set the IED in test mode by

•

configuration, activating the input SIGNAL on the function block TESTMODE.

•

setting

TestMode

to

Enabled

in the local HMI, under

Main menu/Tests/IED test

mode/1:TESTMODE

.

While the IED is in test mode, the output ACTIVE of the function block TESTMODE is
activated. The other outputs of the function block TESTMODE shows the cause of the
"Test mode:

Enabled

" state — input from configuration (OUTPUT signal is activated) or

setting from local HMI (SETTING signal is activated).

While the IED is in test mode, the yellow PICKUP LED will flash and all functions are
blocked. Any function can be unblocked individually regarding functionality and event
signalling.

Forcing of binary output signals is only possible when the IED is in test mode.

Most of the functions in the IED can individually be blocked by means of settings from the
local HMI. To enable these blockings the IED must be set in test mode (output ACTIVE
is activated). When leaving the test mode, and returning to normal operation, these
blockings are disabled and everything is set back to normal operation. All testing will be
done with actually set and configured parameter values within the IED. No settings will
be changed, thus no mistakes are possible.

The blocked functions will still be blocked next time entering the test mode, if the
blockings were not reset. The released function will return to blocked state if test mode is
set to off.

The blocking of a function concerns all output signals from the actual function, so no
outputs will be activated.

1MRK 502 048-UUS A

Section 17

Basic IED functions

681

Technical manual

«
...
685
686
687
688
689
...
»

Содержание Relion











































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Relion

Бренд: SG Intec Ltd & Co KG Страницы: 63

Бренд: Geobrugg Страницы: 60

Бренд: U-Line Страницы: 3

VS-50111, VS-60111, WT-42311,

Бренд: Mitsubishi Страницы: 79

Бренд: Intermatic Страницы: 2

Бренд: Samsung Страницы: 67

Бренд: ABB Страницы: 16

Бренд: Samsung Страницы: 59

Бренд: Panasonic Страницы: 29

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 3

Бренд: Philips Страницы: 2

Бренд: Manson Engineering Industrial Страницы: 8

Бренд: Motor Saver Страницы: 7

Бренд: Energotest Страницы: 97

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды