manualshive.com logo in svg

ABB Relion, Техническое руководство, Страница: 475 / 778

Поделиться
Скачать
ABB Relion Скачать руководство пользователя страница 475

routed. It has a single trip output (TRIP) for connection to one or more of the IEDs binary
outputs, as well as to other functions within the IED requiring this signal.

ANSI05000789 V2 EN

Figure 214:

Simplified logic diagram for three pole trip

Lockout can be activated either by activating the input (SETLKOUT) or automatically
from the trip input by setting 

AutoLock

 to 

Enabled

. A Lockout condition will be indicated

by activation of the output (CLLKOUT). If lockout has been activated it can be reset by
activating the input (RSTLKOUT) or via the HMI.

If 

TripLockout

 is set to 

Enabled

 an active Lockout will latch the three-phase trip output.

In this way if both 

AutoLock

 and 

TripLockout

 are set to 

Enabled

 the trip will always be

three-phase and sealed in.

13.1.7 

Technical data

Table 296:

SMPPTRC (94) technical data

Function

Range or value

Accuracy

Trip action

3-ph

-

Timers

(0.000-60.000) s

± 0.5% ± 10 ms

13.2 

Trip matrix logic TMAGGIO

13.2.1 

Identification

Function description

IEC 61850

identification

IEC 60617

identification

ANSI/IEEE C37.2

device number

Trip matrix logic

TMAGGIO

-

-

1MRK 502 048-UUS A

Section 13

Logic

469

Technical manual

Содержание Relion











































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов