AAON CB-024 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 56

AAON CB-024 Скачать руководство пользователя страница 9

9

1.

Startup and service must be performed
by

a

Factory

Trained

Service

Technician.

2.

The unit is for outdoor use only. See
General Information section for more
unit information.

3.

Every unit has a unique equipment
nameplate with electrical, operational
and

unit

clearance

specifications.

Always refer to the unit nameplate for
specific ratings unique to the model you
have purchased.

4.

READ THE ENTIRE INSTALLATION,
OPERATION AND MAINTENANCE
MANUAL.

OTHER

IMPORTANT

SAFETY

PRECAUTIONS

ARE

PROVIDED THROUGHOUT THIS
MANUAL.

5.

Keep this manual and all literature
safeguarded near or on the unit.

COIL CLEANING

Do not clean DX refrigerant coils with
hot  water  or  steam.  The  use  of  hot
water  or  steam  on  refrigerant  coils
will  cause  high  pressure  inside  the
coil tubing and damage to the coil.

CAUTION

ENCLOSED AREA

Do  not  work  in  an  enclosed  area
where  refrigerant  or  nitrogen  gases
may  be  leaking.  A  sufficient  quantity
of vapors may be present and cause
injury or death

.

WARNING

COMPRESSOR CYCLING

5 MINUTE MINIMUM OFF TIME

To

prevent

motor

overheating

compressors must cycle off for a
minimum of 5 minutes.

5 MINUTE MINIMUM ON TIME

To  maintain  the  proper  oil  level
compressors  must  cycle  on  for  a
minimum of 5 minutes.

The  cycle  rate  must  not  exceed  6
starts per hour.

WARNING

«
...
7
8
9
10
11
...
»

Содержание CB-024

























































Отзывы:

Нет отзывов