AAON CB-024 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 56

AAON CB-024 Скачать руководство пользователя страница 17

17

It  is  recommended  that  the  field  installed
overcurrent  protection  or  disconnect  switch
not be installed on the unit.

Supply voltage must be within the min/max
range  shown  on  the  unit  nameplate.
Available  short  circuit  current  should  not
exceed  the  short  circuit  current  rating
(SCCR) shown on the unit nameplate.

Three  phase  voltage  imbalance  will  cause
motor  overheating  and  premature  failure.
The maximum allowable imbalance is 2.0%.

Voltage  imbalance  is  defined  as  100  times
the  maximum  deviation  from  the  average
voltage divided by the average voltage.

Example:
(221V+230V+227V)/3

=

226V,

then

100*(226V-221V)/226V  =  2.2%,  which
exceeds the allowable imbalance.

Check  voltage  imbalance  at  the  unit
disconnect  switch  and  at  the  compressor
terminal. Contact your local power company
for line voltage corrections.

Installing  contractor  must  check  for  proper
motor  rotation  and  check  blower  motor
amperage  listed  on  the  motor  nameplate  is
not exceeded.

Wire  control  signals  to  the  unit’s  low
voltage  terminal  block  located  in  the
controls compartment.

If any factory installed wiring must be
replaced, use a minimum 105°C type AWM
insulated conductors.

Thermostat

If  a  thermostat  is  used  for  unit  control,
thermostat  should  be  located  on  an  inside
wall  4-5  feet  above  the  floor  where  it  will
not  be  subjected  to  drafts,  sun  exposure,  or
heat  from  electrical  fixtures  or  appliances.
Follow

thermostat

manufacturer’s

instructions

for

general

installation

procedure.

Thermostat control wiring size must be large
enough  to  prevent  excess  voltage  drop  and
ensure proper operation.

All  external  devices  must  be  powered  via  a
separate external power supply.

Units  with  the  modulating  hot  gas  reheat
dehumidification

feature

must

use

a

humidistat  or  a  thermostat  with  a  normally
closed  (NC)  dehumidification  option.  The
following  thermostats  have  been  approved
for usage with the dehumidification feature,

Robertshaw

®

9825i2 Thermostat

Honeywell VisionPRO

®

IAQ Thermostat

AAON Mini Controller

Three phase voltage imbalance will
cause

motor

overheating

and

premature failure.

CAUTION

«
...
15
16
17
18
19
...
»

Содержание CB-024

























































Отзывы:

Нет отзывов