AAON CB-024 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 56

AAON CB-024 Скачать руководство пользователя страница 27

27

Charging Refrigerant & Adjusting
Refrigerant Charge

The  unit  comes  with  full  charge  based  on  a
25  foot  line  set.  Charging  a  system  in  the
field  must  be  based  on  determination  of
liquid sub-cooling and evaporator superheat.
On a system with a TXV, liquid sub-cooling
is  more  representative  of  the  charge  than
evaporator superheat but both measurements
must be taken.

Before Charging

Refer to the Unit Nameplate to determine
which refrigerant must be used to charge the
system.

Unit being charged must be at or near full
load conditions before adjusting the charge.

Units  equipped  with  hot  gas  bypass  must
have  the  hot  gas  bypass  valve  closed  to  get
the proper charge.

Units  equipped  with  hot  gas  reheat  must  be
charged with the hot gas valves closed while
the  unit  is  in  cooling  mode.  After  charging,
unit

should

be

operated

in

reheat

(dehumidification)  mode  to  check  for
correct operation.

Units  equipped  with  heat  pump  options
should be charged in heating mode to get the
proper  charge.    After  charging,  unit  should
be  operated  in  cooling  mode  to  check  for
correct  charge.    Charge  may  need  to  be
adjusted  for  cooling  mode.    If  adjustments
are made in the cooling mode, heating mode
must be rerun to verify proper operation.

After adding or removing charge the system
must be allowed to stabilize, typically 10-15
minutes,

before

making

any

other

adjustments.

The  type  of  unit  and  options  determine  the
ranges for liquid sub-cooling and evaporator
superheat.  Refer  to  the  table  of  acceptable
refrigerant  circuit  values  when  determining
the proper sub-cooling.

Checking Liquid Sub-cooling

Measure the temperature of the liquid line as
it leaves the condenser coil.

Read  the  gauge  pressure  reading  of  the
liquid  line  close  to  the  point  where  the
temperature was taken. You must use liquid
line  pressure  as  it  will  vary  from  discharge
pressure  due  to  condenser  coil  pressure
drop.

Convert the pressure obtained to a saturated
temperature using the appropriate refrigerant
temperature-pressure chart or Table 5 below.

CLEAN AIR ACT

The  Clean  Air  Act  of  1990  bans  the
intentional  venting  of  refrigerant
(CFC’s  and  HCFC’s)  as  of  July  1,
1992. Approved methods of recovery,
recycling  or  reclaiming  must  be
followed.  Fines  and/or  incarceration
may be levied for non-compliance.

CAUTION

COMPRESSOR LUBRICANT

Polyolester (POE) and Polyvinylether
(PVE) oils are two types of lubricants
used  in  hydrofluorocarbon  (HFC)
refrigeration  systems.  Refer  to  the
compressor  label  for  the  proper
compressor lubricant type.

CAUTION

«
...
25
26
27
28
29
...
»

Содержание CB-024

























































Отзывы:

Нет отзывов