AAON CB-024 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 56

AAON CB-024 Скачать руководство пользователя страница 7

7

FIRE,  EXPLOSION  OR  CARBON
MONOXIDE POISONING HAZARD

Failure  to  replace  proper  controls
could  result  in  fire,  explosion  or
carbon  monoxide  poisoning.  Failure
to  follow  safety  warnings  exactly
could result in serious injury, death or
property damage. Do not store or use
gasoline  or  other  flammable  vapors
and  liquids  in  the  vicinity  of  this
appliance.

WARNING

LIVE ELECTRICAL

During installation, testing, servicing,
and troubleshooting of the equipment
it may be necessary to work with live
electrical

components.

Only

a

qualified

licensed

electrician

or

individual properly trained in handling
live

electrical

components

shall

perform these tasks.

Standard

NFPA-70E,

an

OSHA

regulation  requiring  an  Arc  Flash
Boundary  to  be field  established  and
marked  for  identification  of  where
appropriate

Personal

Protective

Equipment (PPE) be worn, should be
followed.

WARNING

GROUNDING REQUIRED

All  field  installed  wiring  must  be
completed  by  qualified  personnel.
Field  installed  wiring  must  comply
with  NEC/CEC,  local  and  state
electrical  code  requirements.  Failure
to  follow  code  requirements  could
result  in  serious  injury  or  death.
Provide

proper

unit

ground

in

accordance

with

these

code

requirements.

WARNING

ROTATING COMPONENTS

Unit  contains  fans  with  moving  parts
that can cause serious injury.  Do  not
remove  grill  containing  fans  until  the
power

to

the

unit

has

been

disconnected and fan has stopped
rotating.

WARNING

3-PHASE ROTATION

Rotation must be checked on all
MOTORS AND COMPRESSORS of
3 phase units at startup by a qualified
service

technician.

Scroll

compressors  are  directional  and  can
be  damaged  if  rotated  in  the  wrong
direction.  Compressor  rotation  must
be  checked  using  suction  and
discharge gauges. Fan motor rotation
should

be

checked

for

proper

operation. Alterations should only be
made at the unit power connection

CAUTION

«
...
5
6
7
8
9
...
»

Содержание CB-024

























































Отзывы:

Нет отзывов