AAON CB-024 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 56

AAON CB-024 Скачать руководство пользователя страница 24

24

How to Use Predetermined Line Sizing

First, read the previous section,

When to Use

Predetermined Line Sizing

, to decide if this

method  is  applicable.  Next,  consult  Table  2
below for pipe diameters.
Examine  Figure  6  below  to  determine  the
acceptable  line  dimensions  associated  with
the  pipe  diameters  determined  in  Table  2
below. The figure is shown as total available
riser  height  versus  total  equivalent  line
length  for  the  liquid  line.  The  curve
identifies  a  region  of  acceptable  piping
configuration  when  the  predetermined  line
sizes are selected for any model in the table.
A piping configuration above the curve falls
outside  the  assumptions  used  to  determine
the line size and will result in a loss of sub-
cooling, and additional pressure losses in the
suction and hot gas lines.

The  total  equivalent  line  length  definition
includes  the  height  of  vertical  rise,  pressure
drop  through  elbows  and  accessories,  and
horizontal

line

length,

so

elbows,

accessories,  and  vertical  rise  must  be
considered  when  determining  horizontal
length  available  from  the  total  equivalent
line length.

The figure below is presented in terms of the
liquid  line,  but  it  assumes  that  the  suction
line  length  is  similar,  as  these  lines  are
commonly  routed  together  to  minimize  the
space  and  cost  required  for  split  system
installation.

Before using this table read the

When to Use Predetermined Line
Sizes

section. Do not assume that

these line sizes are appropriate for
every case. Consult ASHRAE
Handbook

–

Refrigeration

for

generally accepted system piping
practices. The AAON

Refrigerant

Piping Calculator

in Ecat32 can be

used for job specific line sizing.

CAUTION

«
...
22
23
24
25
26
...
»

Содержание CB-024

























































Отзывы:

Нет отзывов