AAON CB-024 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 56

AAON CB-024 Скачать руководство пользователя страница 6

6

ELECTRIC SHOCK

Electric

shock

hazard.

Before

servicing, shut off all electrical power
to

the

unit,

including

remote

disconnects, to avoid shock hazard
or injury from rotating parts. Follow
proper Lockout-Tagout procedures.

WARNING

Safety

Attention should be paid to the following statements:

NOTE

- Notes are intended to clarify the unit installation, operation and maintenance.

CAUTION

- Caution statements are given to prevent actions that may result in

equipment damage, property damage, or personal injury.

WARNING

- Warning statements are given to prevent actions that could result in

equipment damage, property damage, personal injury or death.

DANGER

- Danger statements are given to prevent actions that will result in equipment

damage, property damage, severe personal injury or death.

ELECTRIC

SHOCK,

FIRE

OR

EXPLOSION HAZARD

Failure  to  follow  safety  warnings
exactly  could  result  in  dangerous
operation,  serious  injury,  death  or
property damage.

Improper  servicing  could  result  in
dangerous  operation,  serious  injury,
death, or property damage.



When servicing controls, label all
wires

prior

to

disconnecting.

Reconnect wires correctly.



Verify proper operation after
servicing. Secure all doors with
key-lock or nut and bolt.

WARNING

QUALIFIED INSTALLER

Improper

installation,

adjustment,

alteration, service or maintenance
can

cause

property

damage,

personal injury or loss of  life.  Startup
and  service  must  be  performed  by  a
Factory  Trained  Service  Technician.
A  copy  of  this  IOM  should  be  kept
with the unit.

WARNING

«
...
4
5
6
7
8
...
»

Содержание CB-024

























































Отзывы:

Нет отзывов