AAON CB-024 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 56

AAON CB-024 Скачать руководство пользователя страница 55

Literature Change History
November 2009

Update of manual formatting to match with other IOMs and adding variable capacity scroll
compressor information.

April 2012

Added oil drip note below piping diagrams. Updated the Startup Form.

May 2012

Updated the Table of Contents.

March 2013

Update of the manual revising Table S1 - Sub-Cooling and Superheat, adding Table S2 -
Performance Testing Air Flow Setpoints, adding information about compressor cycling.

June 2013

Updated piping diagrams to show internal modulating hot gas reheat and hot gas bypass valves.
New part number assigned.

July 2014

Updated service clearance drawing.

February 2015

Updated Feature 5 options to reflect standard exterior corrosion protection.

July 2015

Updated Replacement Parts instructions. Added Features and Options section.

August 2016

Added  Storage  information.    Added  guidelines  for  variable  capacity  compressors  in  the  line
sizing section.  Added double riser schematics and discussion for heat pump operation.  Added a
section about oil level under the refrigerant line sizing section.  Added a section on compressor
lockouts.    Included  heat  pump  charging  guidelines  in  the  Acceptable  Refrigeration  Circuit
Values  Table.    Added  Special  Low  Ambient  Option  Charging  Instructions.    Changed  e-coated
coil cleaning to100 psi water pressure.

December 2016

Fixed a reference error.

«
...
53
54
55
56
»

Содержание CB-024

























































Отзывы:

Нет отзывов