AAON CB-024 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 56

AAON CB-024 Скачать руководство пользователя страница 15

15

corner of the unit is recommended for
service.

Figure 2 – Condensing Unit Clearances

Condensing units should not be installed in
an enclosure or pit that is deeper than the
height

of

the

unit.

When

recessed

installation  is  necessary,  the  clearance  to
maintain proper airflow is at least three feet.

CB  Series  condensing  units  are  single
circuited  with  vertical  air  discharge.  There
must be no obstruction above the equipment.
Do not place the unit under an overhang.

Placement relative to the building air intakes
and  other  structures  must  be  carefully
selected. Consider the effects of outdoor fan
noise on conditioned space and any adjacent
occupied  space.  It  is  recommended  that  the
unit  be  placed  so  that  discharge  does  not
blow  toward  windows  less  than  25  feet
away.

Heat

pumps

require special location

consideration

in

areas

where

snow

accumulation  can  become  an  obstruction
and  in  areas  with  prolonged  continuous
subfreezing  temperatures.  Heat  pump  unit
bases  are  cutout  under  the  outdoor  coil  to
permit  drainage  of  frost  accumulation.  The
unit  must  be  situated  to  permit  free
unobstructed  drainage  of  the  defrost  water
and  ice.  A  minimum  3  inches  clearance
under  the  outdoor  coil  is  required  in  the
milder  climates.  In  more  severe  weather

locations, it is recommended that the unit be
elevated to allow unobstructed drainage and
airflow.

Table 1 - Recommended Elevation

Minimums

Design

Temperature

Suggest Minimum

Elevation

+15



F and above

3”

-5



F to +17



F

8”

Below -5



F

12”

Mounting Isolation

For roof mounted applications or anytime
vibration transmission is a factor, vibration
isolators may be used.

Access Panel

Access  panel  is  provided  to  electrical
compartment.    To  remove  the  panel,
unscrew the four screws

PVC PIPING

PVC  (Polyvinyl  Chloride)  and  CPVC
(Chlorinated  Polyvinyl  Chloride)  are
vulnerable  to  attack  by  certain
chemicals.  Polyolester  (POE)  oils
used

with

R-410A

and

other

refrigerants,  even  in  trace  amounts,
in a PVC or CPVC piping system will
result in stress cracking of  the piping
and  fittings  and  complete  piping
system failure.

CAUTION

«
...
13
14
15
16
17
...
»

Содержание CB-024

























































Отзывы:

Нет отзывов