AAON CB-024 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 56

AAON CB-024 Скачать руководство пользователя страница 11

11

General Description

AAON CB Series condensing units have
been designed for outdoor installation only.
Startup and service must be performed by a
Factory Trained Service Technician.

Codes and Ordinances

CB  Series  units  have  been  tested  and
certified,  by  ETL,  in  accordance  with  UL
Safety Standard 1995/CSA C22.2 No. 236.

System  should  be  sized  in  accordance  with
the

American

Society

of

Heating,

Refrigeration

and

Air

Conditioning

Engineers Handbook.

Installation of CB Series units must conform
to  the  ICC  standards  of  the  International
Mechanical Code, the International Building
Code,  and  local  building,  plumbing  and
waste  water  codes.  All  appliances  must  be
electrically  grounded  in  accordance  with
local codes, or in the absence of local codes,
the

current

National

Electric

Code,

ANSI/NFPA 70 or the current Canadian
Electrical Code CSA C22.1.

Receiving Unit

When  received,  the  unit  should  be  checked
for  damage  that  might  have  occurred  in
transit. If damage is found it should be noted
on  the  carrier’s  Freight  Bill.  A  request  for
inspection by carrier’s agent should be made
in writing at once.

Nameplate  should  be  checked  to  ensure  the
correct  model  sizes  and  voltages  have  been
received to match the job requirements.

If  repairs  must  be  made  to  damaged  goods,
then  the  factory  should  be  notified  before
any repair action is taken in order to protect
the  warranty.    Certain  equipment  alteration,
repair,  and  manipulation  of  equipment
without  the  manufacturer’s  consent  may
void  the  product  warranty.    Contact  AAON
Warranty  Department  for  assistance  with
handling  damaged  goods,  repairs,  and
freight claims: (903) 236-4403.

NOTE:  Upon  receipt  check  shipment  for
items  that  ship  loose.    Consult  order  and
shipment documentation to identify potential
loose-shipped  items.    Loose-shipped  items

The  Clean  Air  Act  of  1990  bans  the
intentional venting of refrigerant as of
July  1,  1992.  Approved  methods  of
recovery,  recycling,  or  reclaiming
must be followed.

CAUTION

QUALIFIED INSTALLER

Improper

installation,

adjustment,

alteration, service or maintenance
can

cause

property

damage,

personal  injury  or  loss  of  life.
Installation  and  service  must  be
performed  by  a  Factory  Trained
Service Technician.

WARNING

SHARP EDGES

Coils and sheet metal surfaces
present sharp edges and care must
be

taken

when

working

with

equipment.

WARNING

Failure  to  observe  the  following
instructions  will  result  in  premature
failure  of  your  system  and  possible
voiding of the warranty.

WARNING

«
...
9
10
11
12
13
...
»

Содержание CB-024

























































Отзывы:

Нет отзывов