AAON CB-024 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 56

AAON CB-024 Скачать руководство пользователя страница 35

35

The  low  ambient  system  maintains  normal
head pressure during periods of low ambient
by restricting liquid flow from the condenser
to  the  receiver,  and  at  the  same  time
bypassing  hot  gas  around  the  condenser  to
the inlet of the receiver. This reduces liquid
refrigerant  flow  from  the  condenser,
reducing its  effective  surface  area, which in
turn  increases  the  condensing  pressure.  At
the  same  time  the  bypassed  hot  gas  raises
liquid  pressure  in  the  receiver,  allowing  the
system  to  operate  properly.  CF  Series
condensers  and  condensing  units  use  an
LAC valve for low ambient operation.

LAC Valve

The Low Ambient Control (LAC) valve is a
non-adjustable

three

way

valve

that

modulates to  maintain receiver pressure.  As
the  receiver  pressure  drops  below  the  valve
setting  (295  psig  for  R-410A),  the  valve
modulates  to  bypass  discharge  gas  around
the condenser. The discharge gas warms the
liquid in the receiver and raises the pressure
to  the  valve  setting.  The  following
schematic  shows  an  example  system  using
the LAC valve.

Figure 10 - Piping Schematic of Example System using the LAC Valve

«
...
33
34
35
36
37
...
»

Содержание CB-024

























































Отзывы:

Нет отзывов