manualshive.com logo in svg

AAON CB-024, Установка, эксплуатация и обслуживание, Страница: 37 / 56

Поделиться
Скачать
AAON CB-024 Скачать руководство пользователя страница 37

 

 

37 

Maintenance 

(See  back  of  the  manual  for  maintenance 
log.) 
 
At  least  once  each  year,  a  qualified  service 
technician  should  check  out  the  unit.  This 
includes  reading  and  recording  suction 
pressures  and  checking  for  normal  sub-
cooling and superheat. 
 
 
 
 
 
 
 
 
 
 
 
Only 

trained 

and 

qualified 

service 

technicians  experienced  in  both  condensing 
units  and  air  conditioning  are  permitted  to 
service  the  CB  Series  units  to  keep 
warranties in effect. 

 

 
Coils 

The  condenser  coils  should  be  inspected 
yearly  to  ensure  unrestricted  airflow.  If  the 
coils contain a large amount of airborne dust 
or  other  material,  they  should  be  cleaned. 
Care must be taken to prevent bending of the 
aluminum fins on the coils.  
 
Before  attempting  to  clean  the  coils;  set 
thermostat  to  the  "OFF"  position;  turn  the 
electrical  power  to  the  unit  to  the  "OFF" 
position  at  the  disconnect  switch.  The 
condenser  coil  can  be  cleaned  by  washing 
from  the  inside  out  with  water  and  a  coil 
cleaner.  If  coil  is  extremely  dirty  with 
clogged 

fins, 

a 

service 

professional 

specializing  in  coil  cleaning  should  be 
called. 
 

E-Coated Coil Cleaning 

Documented  routine  cleaning  of  e-coated 
coils  is  required  to  maintain  coating 
warranty coverage. 
 
 
 
 
 
 
 
 
 
Surface  loaded  fibers  or  dirt  should  be 
removed  prior  to  water  rinse  to  prevent 
restriction of airflow. If unable to back wash 
the  side  of  the  coil  opposite  of  the  coils 
entering  air  side,  then  surface  loaded  fibers 
or  dirt  should  be  removed  with  a  vacuum 
cleaner. If a vacuum cleaner is not available, 
a 

soft  non-metallic

  bristle  brush  may  be 

used.  In  either  case,  the  tool  should  be 
applied  in  the  direction  of  the  fins.  Coil 
surfaces  can  be  easily  damaged  (fin  edges 
bent  over)  if  the  tool  is  applied  across  the 
fins. 
 
Use  of  a  water  stream,  such  as  a  garden 
hose, against a surface loaded coil will drive 
the  fibers  and  dirt  into  the  coil.  This  will 
make cleaning efforts more difficult. Surface 
loaded  fibers  must  be  completely  removed 
prior to using low velocity clean water rinse. 
 
A 

monthly

 

clean 

water 

rinse 

is 

recommended  for  coils  that  are  applied  in 
coastal or industrial environments to help to 
remove chlorides, dirt, and debris. It is very 
important 

when 

rinsing, 

that 

water 

temperature  is  less  than  130°F  and  pressure 
is  than  100  psig  to  avoid  damaging  the  fin 
edges. An elevated water temperature (not to 
exceed  130°F)  will  reduce  surface  tension, 
increasing  the  ability  to  remove  chlorides 
and dirt. 
 

 
 

 

Improper 

installation, 

adjustment, 

alteration,  service  or  maintenance 
can 

cause 

property 

damage, 

personal  injury  or  loss  of  life. 
Installation  and  service  must  be 
performed  by  a  trained,  qualified 
installer.  

    

 

WARNING

 

 

 
Electric  shock  hazard.  Shut  off  all 
electrical  power  to  the  unit  to  avoid 
shock  hazard  or  injury  from  rotating 
parts.

 

    

 

WARNING

 

Содержание CB-024

























































Отзывы:

Нет отзывов