manualshive.com logo in svg

AAON CB-024, Установка, эксплуатация и обслуживание, Страница: 12 / 56

Поделиться
Скачать
AAON CB-024 Скачать руководство пользователя страница 12

 

 

12 

may have been placed inside the unit cabinet 
for  security.    Installers  and  owners  should 
secure all doors with locks or nuts and bolts 
to prevent unauthorized access. 
 
The warranty card must be completed in full 
and  returned  to  AAON  not  more  than  3 
months after the unit is delivered. 
 

Storage 

If  installation  will  not  occur  immediately 
following delivery, store equipment in a dry 
protected  area  away  from  construction 
traffic  and  in  the  proper  orientation  as 
marked  on  the  packaging  with  all  internal 
packaging in place. Secure all loose-shipped 
items. 
 

Direct Expansion (DX) Condensing Units 

CB  Series  condensing  units  are  factory 
assembled and wired, including a full charge 
of  R-410A  refrigerant  for  up  to  25  feet  of 
line  set.  Systems  with  the  modulating  hot 
gas  reheat  option  will  require  refrigerant  to 
be  field  added  because  of  the  additional 
refrigerant 

components 

and 

piping 

associated with the system. 
 
Failure to observe the following instructions 
may  result  in  premature  failure  of  your 
system,  and  possible  voiding  of  the 
warranty. 
 
 

 
 
 
 
 
 
 
 
 
 
 

 

Never  cut  off  the  main  power  supply  to  the 
unit,  except  for  servicing,  emergency,  or 
complete shutdown of the unit. When power 
is  cut  off  from  the  unit,  compressors  using 
crankcase heaters  cannot prevent  refrigerant 
migration.  This  means  the  compressor  may 
cool  down  and  liquid  refrigerant  may 
accumulate  in  the  compressor.  Since  the 
compressor  is  designed  to  pump  refrigerant 
gas,  damage  may  occur  when  power  is 
restored.

 

 

If  power  to  the  unit  must  be  off  for  more 
than  an  hour,  turn  the  thermostat  system 
switch  to  “Off”,  or  turn  the  unit  off  at  the 
control  panel,  and  then  cut  off  the  main 
power  supply.  Leave  the  unit  off  until  the 
main power supply has been turned on again 
for  at  least  24  hours.  This  will  give  the 
crankcase  heater  time  to  clear  any  liquid 
accumulation out of the compressor before it 
is required to run. 
 
Always  control  the  system  from  the 
thermostat,  or  control  panel,  never  at  the 
main  power  supply,  except  for  servicing, 
emergency,  or  complete  shutdown  of  the 
unit. 
 
The  standard  compressors  must  be  on  a 
minimum  of  5  minutes  and  off  for  a 
minimum of 5 minutes. The cycle rate must 
be no more than 6 starts per hour. 
 
The  variable  capacity  compressors  must  be 
on  a  minimum  of  3  minutes  and  off  for  a 
minimum of 3 minutes. The cycle rate must 
be no more than 10 starts per hour. 
 
The  compressor  life  will  be  seriously 
shortened  by  reduced  lubrication,  and  the 
pumping  of  excessive  amounts  of  liquid  oil 
and liquid refrigerant. 
 

 
 

 

CRANKCASE HEATER 

OPERATION 

 

Units  are  equipped  with  compressor 
crankcase  heaters,  which  should  be 
energized  at  least  24  hours  prior  to 
cooling  operation,  to  clear  any  liquid 
refrigerant from the compressors. 

 
 

  

 

CAUTION 

 

Содержание CB-024

























































Отзывы:

Нет отзывов