AAON CB-024 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 56

AAON CB-024 Скачать руководство пользователя страница 14

14

Installation

AAON equipment has been designed for
quick and easy installation.

Lifting the Unit

CB  Series  condensing  units  have  channels
underneath  the  base  which  provide  lifting
access to the underside of the equipment and
allow  moving  and  placement  without
physical damage.

Figure 1 – Forklift Channels & Access Panel

Dollies and/or carts are recommended to lift
and  place  the  unit  to  prevent  damage  to  the
equipment and injury to the installer.

Care should be taken if using spreader bars,
blocking,  or  other  lifting  devices  to  prevent
any  damage  to  the  cabinet,  coil  or
condensing fans.

Before  lifting  unit,  be  sure  that  all  shipping
material has been removed from unit.

Hoist  unit  to  a  point  directly  above  the
condenser  pad,  and  lower  unit  into  the
proper  place.  Unit  may  also  be  positioned

with a dolly. When the unit is in place,
remove the dolly or lifting device. Make
sure the unit is properly seated and level.

Locating Unit

CB Series condensing units are designed for
outdoor application and placement at ground
level  or  on  a  rooftop.  Units  must  be  placed
on  a  level  and  solid  foundation  that  can
support the unit’s weight.

When  rooftop  mounted,  a  steel  frame  must
be provided that will support the unit above
the roof itself for load distribution.

When  installed  at  ground  level,  a  one-piece
concrete  slab  or  composite  condenser  pad
should  be  used  with  footings  that  extend
below  the  frost  line  (a  substantial  base  that
will  not  settle).  Slab  should  be  surrounded
by  a  graveled  area  for  proper  drainage  and
should not adjoin the building as sound and
vibration  may  be  transmitted  to  the
structure. Care must also be taken to protect
the  coils  and  fins  from  damage  due  to
vandalism or other hazards.

Airflow  to  and  from  the  condensing  unit
must  not  be  restricted.  Coils  and  fans  must
be  free  of  any  obstructions  and  debris  in
order  to  start  and  operate  properly  with  a
correct amount of airflow. Obstruction to air
flow  will  result  in  decreased  performance
and efficiency.

The  installation  position  must  provide  at
least one foot of clearance from the wall for
proper  air  flow  to  the  coils.  When  multiple
units are mounted adjacent to each other, the
clearance  required  between  them  is  three
feet.

Service compartment must be accessible for
periodic  servicing  of  controls,  safety
devices,  and  refrigerant  service/shutoff
valves. At least two feet of clearance on this

Incorrect lifting can cause damage to
the unit.

CAUTION

«
...
12
13
14
15
16
...
»

Содержание CB-024

























































Отзывы:

Нет отзывов