AAON CB-024 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 56

AAON CB-024 Скачать руководство пользователя страница 18

18

Refrigerant Piping

(See back of the manual for refrigerant
piping diagrams.)

General

Piping  from  the  condensing  unit  to  the  air
handler is the responsibility of the installing
contractor.

Use  only  clean  type  “ACR”  copper  tubing
that  has  been  joined  with  high  temperature
brazing alloy.

The  pipe  or  line  sizes  must  be  selected  to
meet  the  actual  installation  conditions  and
not  simply  based  on  the  connection  sizes  at
the condensing unit or air handler.

All CB Series condensing units are provided
with in-line shutoff valves on both the liquid
and  suction  lines.  These  should  remain
closed  until  the  system  is  ready  for  start-up
after installation.

Piping should conform to generally accepted
practices and codes.

Upon  completion  of  piping  connection,  the
interconnecting  piping  and  air  handler

MUST BE evacuated to 500 microns or less;
leak checked and charged with refrigerant.

Determining Refrigerant Line Size

The piping between the condenser and low
side must ensure:

1. Minimum pressure drop,

and

2. Continuous oil return,

and

3.  Prevention  of  liquid  refrigerant  slugging,
or carryover

Minimizing  the  refrigerant  line  size  is
favorable  from  an  economic  perspective,
reducing installation costs, and reducing the
potential  for  leakage.  However,  as  pipe
diameters

narrow,

pressure-reducing

frictional forces increase.

Excessive  suction  line  pressure  drop  causes
loss  of  compressor  capacity  and  increased
power  usage  resulting  in  reduced  system
efficiency.  Excessive  pressure  drops  in  the
liquid line can cause the liquid refrigerant to
flash, resulting in faulty Thermal Expansion
Valve  (TXV)  operation  and  improper
system  performance.  In  order  to  operate
efficiently  and  cost  effectively,  while
avoiding  malfunction,  refrigeration  systems
must be designed to minimize both cost and
pressure loss.

REFRIGERANT PIPING

This  section  is  for  information  only
and  is  not  intended  to  provide  all
details  required  by  the  designer  or
installer  of  the  refrigerant  piping
between

the

condenser

or

condensing unit and the air handling
unit. AAON, Inc. is not responsible for
interconnecting

refrigerant

piping.

Consult

ASHRAE

Handbook

–

Refrigeration and ASME Standards.

CAUTION

REFRIGERANT PIPING

Line sizes must be selected to meet
actual installation conditions, not
simply based on the connection sizes
at the condensing unit or air handling
unit.

CAUTION

«
...
16
17
18
19
20
...
»

Содержание CB-024

























































Отзывы:

Нет отзывов