AAA RT40 Скачать руководство пользователя страница 25

Страница: 25 / 165

Controls - 24

RT40 Operator’s Manual

Center Console

CMW

Indicators

Engine oil pressure indicator

Engine oil temperature indicator

Cold start wait indicator *

Hydraulic fluid temperature indicator

Start interlock

* optional

Item

Description

Notes

Engine oil pressure
indicator

Lights when oil pressure falls
below 8-12 psi (.5-.8 bar).
Light will come on briefly
when engine is started.

If light remains on:

•

Turn off engine.

•

Check oil level.

•

If pressure is still low, consult
engine manual.

Engine oil temperature
indicator

Lights and engine shuts down
if engine oil temperature rises
above 275° F (135° C). Light
will come on briefly when
engine is started.

If light remains on:

•

Turn off engine and let it cool.

•

Check fan belt tension.

•

Check for low engine oil level.

•

Check cooling fins for dirt and
debris.

t14om005h.eps

*Always follow manufacturer instructions*

*AAA Rent-All 225-291-1356*

Содержание RT40






































































































































































Результаты поиска

Содержание RT40

Отзывы:

Похожие инструкции для RT40

Бренды по названию

Популярные бренды

AAA RT40, Руководство оператора

Результаты поиска

Содержание RT40

Отзывы:

Похожие инструкции для RT40

Бренды по названию

Популярные бренды