AAA RT40 Скачать руководство пользователя страница 81

Страница: 81 / 165

Plow - 80

RT40 Operator’s Manual

Operation

CMW

Operation

Crushing weight could cause death or serious injury. Use proper

procedures and equipment or stay away.

Electrical shock. Contacting electrical lines will cause death or serious

injury. Know location of lines and stay away.

NOTICE:

Cutting high voltage cable can cause electrocution. Expose lines by hand before digging.

Incorrect procedures could result in death, injury, or property damage.

Learn to use equipment correctly.

NOTICE:

•

Comply with all utility notification regulations before digging or drilling.

•

Notify companies that do not subscribe to One-Call.

•

Do not drive backward with plow in the ground.

*Always follow manufacturer instructions*

*AAA Rent-All 225-291-1356*

Содержание RT40






































































































































































Результаты поиска

Содержание RT40

Отзывы:

Бренды по названию

Популярные бренды

AAA RT40, Руководство оператора

Результаты поиска

Содержание RT40

Отзывы:

Бренды по названию

Популярные бренды