AAA RT40 Скачать руководство пользователя страница 74

Страница: 74 / 165

RT40 Operator’s Manual

Trench - 73

Operation

CMW

Operation

Jobsite hazards could cause death or serious injury. Use correct

equipment and work methods. Use and maintain proper safety equipment.

NOTICE:

Cutting or drilling concrete containing sand or rock containing quartz may result in exposure to

silica dust. Use respirator, water spray or other means to control dust. Silica dust can cause lung
disease and is known to the State of California to cause cancer.

Electrical shock. Contacting electrical lines will cause death or serious

injury. Know location of lines and stay away.

NOTICE:

Cutting high voltage cable can cause electrocution. Expose lines by hand before

digging.

Incorrect procedures could result in death, injury, or property damage.

Learn to use equipment correctly.

NOTICE:

•

Comply with all utility notification regulations before digging or drilling.

•

Notify companies that do not subscribe to One-Call.

Flying objects thrown by machine may strike people. Wear hard hat and

safety glasses.

Moving digging teeth will cause death or serious injury. Stay away.

NOTICE:

•

Ensure parking brake is engaged and parking brake indicator is on.

•

Machine might jerk when digging starts. Allow 3’ (1 m) between digging teeth and obstacle.

•

Keep everyone at least 6’ (2 m) from machine, attachments, and their range of movement.

*Always follow manufacturer instructions*

*AAA Rent-All 225-291-1356*

Содержание RT40






































































































































































Результаты поиска

Содержание RT40

Отзывы:

Бренды по названию

Популярные бренды

AAA RT40, Руководство оператора

Результаты поиска

Содержание RT40

Отзывы:

Бренды по названию

Популярные бренды