AAA RT40 Скачать руководство пользователя страница 107

Страница: 107 / 165

Complete the Job - 106

RT40 Operator’s Manual

Restore Jobsite

CMW

Restore Jobsite

After product is installed, return spoils to the trench
with backfill blade.

Backfilling

Position unit at end of trench, several feet from
spoils. Aim tractor at outer edge of spoils.

Adjust backfill blade to fit land contour.

Move outer edge of spoils toward trench. Take
two or more passes at spoils rather than moving
all spoils at once.

Repeat on other side of trench, if necessary.

Engage float and make final pass in reverse
over trench.

Rinse Equipment

Spray water onto equipment to remove dirt and mud.

Stow Tools

Make sure all tools and accessories are loaded on trailer.

NOTICE:

Do not spray water onto operator’s console. Electrical components could be damaged. Wipe

down instead.

*Always follow manufacturer instructions*

*AAA Rent-All 225-291-1356*

Содержание RT40






































































































































































Результаты поиска

Содержание RT40

Отзывы:

Бренды по названию

Популярные бренды

AAA RT40, Руководство оператора

Результаты поиска

Содержание RT40

Отзывы:

Бренды по названию

Популярные бренды