AAA RT40 Скачать руководство пользователя страница 19

Страница: 19 / 165

Safety - 18

RT40 Operator’s Manual

Emergency Procedures

CMW

If an Electric Line is Damaged

If you suspect an electric line has been damaged and you are

on tractor

, DO NOT MOVE. Remain on

tractor and take the following actions. The order and degree of action will depend upon the situation.

•

Warn people nearby that an electric strike has occurred. Instruct them to leave the area and contact
utility.

•

Raise attachments and drive from immediate area.

•

Contact utility company to shut off power.

•

Do not return to jobsite or allow anyone into area until given permission by utility company.

If you suspect an electric line has been damaged and you are

off tractor

, DO NOT TOUCH TRACTOR.

Take the following actions. The order and degree of action will depend upon the situation.

•

LEAVE AREA. The ground surface may be electrified, so take small steps with feet close together to
reduce the hazard of being shocked from one foot to the other. For more information, contact your
Ditch Witch dealer.

•

Contact utility company to shut off power.

•

Do not return to jobsite or allow anyone into area until given permission by utility company.

*Always follow manufacturer instructions*

*AAA Rent-All 225-291-1356*

Содержание RT40






































































































































































Результаты поиска

Содержание RT40

Отзывы:

Похожие инструкции для RT40

Бренды по названию

Популярные бренды

AAA RT40, Руководство оператора

Результаты поиска

Содержание RT40

Отзывы:

Похожие инструкции для RT40

Бренды по названию

Популярные бренды