AAA RT40 Скачать руководство пользователя страница 88

Страница: 88 / 165

RT40 Operator’s Manual

Saw - 87

Operation

CMW

Adjust throttle to low idle.

Move attachment speed/direction control to desired speed. SAW WILL TURN.

Increase engine speed to full throttle.

Slowly lower saw to trench depth.

Raise backfill blade.

Release parking brake.

Push ground drive control forward to trenching speed.

When trench is complete, move ground drive control to neutral and adjust throttle to low idle.

Raise saw and stabilizers.

10. As saw clears top of trench, move attachment speed/direction control to neutral.

11. Drive a short distance away from work site.

12. Shut down tractor. See page 60 for correct shutdown procedures.

Incorrect procedures could result in death, injury, or property

damage. Learn to use equipment correctly.

NOTICE:

Ensure that stabilizers are in contact with the ground while sawing. Failure to use

stabilizers correctly will damage equipment.

*Always follow manufacturer instructions*

*AAA Rent-All 225-291-1356*

Содержание RT40






































































































































































Результаты поиска

Содержание RT40

Отзывы:

Бренды по названию

Популярные бренды

AAA RT40, Руководство оператора

Результаты поиска

Содержание RT40

Отзывы:

Бренды по названию

Популярные бренды