manualshive.com logo in svg

AAA RT40, Руководство оператора

Поделиться
Скачать
AAA RT40 Скачать руководство пользователя страница 8

RT40 Operator’s Manual

Foreword - 7

CMW

Foreword

This manual is an important part of your equipment. It provides safety information and operation 
instructions to help you use and maintain your Ditch Witch equipment. 

Read this manual before using your equipment. Keep it with the equipment at all times for future reference. 
If you sell your equipment, be sure to give this manual to the new owner.

If you need a replacement copy, contact your Ditch Witch dealer. If you need assistance in locating a 
dealer, visit our website at 

www.ditchwitch.com

 or write to the following address: 

The Charles Machine Works, Inc.
Attn: Marketing Department
PO Box 66
Perry, OK 73077-0066 
USA

The descriptions and specifications in this manual are subject to change without notice. The Charles 
Machine Works, Inc. reserves the right to improve equipment. Some product improvements may have 
taken place after this manual was published. For the latest information on Ditch Witch equipment, see your 
Ditch Witch dealer.

Thank you for buying and using Ditch Witch equipment.

*Always follow manufacturer instructions*

*AAA Rent-All 225-291-1356*

Содержание RT40






































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды