AAA RT40 Скачать руководство пользователя страница 68

Страница: 68 / 165

RT40 Operator’s Manual

Transport - 67

Haul

CMW

Load

Fasten and adjust seat belt.

Start tractor. See page 58 for proper start-up procedures.

Raise attachments, but keep them low.

Move attachments to center position and check that they are not in float.

Release parking brake.

Slowly drive tractor onto trailer.

Position tractor on trailer deck for proper weight distribution.

Engage parking brake.

Lower attachments to trailer bed and turn tractor off. See page 60 for proper shutdown procedures.

10. Attach chains to tractor and attachments where tiedown decals are located. See page 65.

Crushing weight. If load falls or moves it could kill or crush you. Use

proper procedures and equipment or stay away.

NOTICE:

•

Attach trailer to tow vehicle before loading or unloading.

•

Load and unload trailer on level ground.

•

Put manual transmission into first or reverse gear or automatic transmission into park. Turn off
ignition. Set parking brake.

•

Block trailer wheels.

•

Incorrect loading can cause trailer swaying.

Rollover possible. If machine rolls over, you could be thrown from seat

and killed or crushed. Wear seat belt.

*Always follow manufacturer instructions*

*AAA Rent-All 225-291-1356*

Содержание RT40






































































































































































Результаты поиска

Содержание RT40

Отзывы:

Похожие инструкции для RT40

Бренды по названию

Популярные бренды

AAA RT40, Руководство оператора

Результаты поиска

Содержание RT40

Отзывы:

Похожие инструкции для RT40

Бренды по названию

Популярные бренды