AAA RT40 Скачать руководство пользователя страница 82

Страница: 82 / 165

RT40 Operator’s Manual

Plow - 81

Operation

CMW

Fasten and adjust seat belt.

Start tractor.

Adjust throttle to low idle.

Check that ground drive control is in neutral.

If equipped with combo, move selector valve to plow position. If equipped with backfill blade tilt/
attachment swing valve and control, move selector to swing position.

Raise backfill blade.

Move ground drive control forward to plowing speed and lower plow blade into ground.

Move plow lift control to float.

Move plow swing control to float.

10. Increase engine speed to full throttle.

NOTICE:

•

Lower plow into ground before moving plow lift control or plow swing control to float.

•

Do NOT move ground drive to reverse with plow blade in the ground.

*Always follow manufacturer instructions*

*AAA Rent-All 225-291-1356*

Содержание RT40






































































































































































Результаты поиска

Содержание RT40

Отзывы:

Похожие инструкции для RT40

Бренды по названию

Популярные бренды

AAA RT40, Руководство оператора

Результаты поиска

Содержание RT40

Отзывы:

Похожие инструкции для RT40

Бренды по названию

Популярные бренды