A-Neu Video ANI-4KANA страница 19 Скачать руководство пользователя

Страница: 19 / 68

RS-232 Protocol & Telnet Commands

COMMAND

DESCRIPTION

$EDID_RX N1

Select the EDID to use with the unit’s HDMI input (Rx).

Available values for

D1~D10 [Default EDID 1~10]
C1~C10 [Copy EDID 1~10]

SINK

[Currently connected HDMI sink]

$EDID_RX?

Display the current EDID selection for the unit’s HDMI input (Rx).

$EDID_TYPE? N1

Display the EDID type of the selected location.

Available values for

[HDMI Input (Rx) Port]

SINK_H [HDMI Sink]
SINK_V [VGA Sink]

NOTE:

•

If the EDID fails to be read,

“$err_ddc”

will be displayed.

•

If the EDID has invalid content,

“$err_bad”

will be displayed.

$EDID_WRITE

N1,N2 N3

Directly write an EDID block to the selected EDID location.

Available values for

[HDMI Input (Rx) Port]

SINK_H [HDMI Sink]
SINK_V [VGA Sink]

= BLOCK0~BLOCK1

= <CR><LF>{128 byte hex data}

NOTE:

•

The data must be sent as a 128 byte hex data bit stream

following the <CR><LF> in the N3 part of the command.

• Each hex data unit is composed of 3 digits. The ﬁrst 2 digits are

the hex value. The 3rd digit is a space (0x20).

• If the sum of the 128 byte data isn’t 0,

“$err_ checksum”

will be

displayed.

$FACTORY

Execute a factory reset and reboot the unit.

NOTE:

Stored Copy EDIDs and Ethernet settings will not be

reset.

$FWVER?

Display the current firmware version.

$HDCP_IN_SW N1

Enable or disable HDCP support for the unit’s HDMI input.

= ON, OFF

NOTE:

Affects Analyzer mode only.

Содержание ANI-4KANA





































































Результаты поиска

Содержание ANI-4KANA

Отзывы:

Похожие инструкции для ANI-4KANA

Бренды по названию

Популярные бренды

A-Neu Video ANI-4KANA, Инструкция по эксплуатации

Результаты поиска

Содержание ANI-4KANA

Отзывы:

Похожие инструкции для ANI-4KANA

Бренды по названию

Популярные бренды