A-Neu Video ANI-4KANA страница 46 Скачать руководство пользователя

Страница: 46 / 68

Test PATTERNS

19. CROSS HATCH 8 (2 VARIATIONS)

The

Cross Hatch 8

pattern is a full field black & white pattern of crossing vertical and

horizontal lines dividing the screen into (8) sections in each direction. This pattern is

primarily used to check for color convergence and pincushion issues in projectors. There

are (2) variations: Normal (white lines, black field) and Inverse (black lines, white field).

20. CROSS HATCH 16 (2 VARIATIONS)

The

Cross Hatch 16

pattern is a full field black & white pattern of crossing vertical and

horizontal lines dividing the screen into (16) sections in each direction. This pattern is

primarily used to check for color convergence and pincushion issues in projectors. There

are (2) variations: Normal (white lines, black field) and Inverse (black lines, white field).

21. CROSS HATCH 32 (2 VARIATIONS)

The

Cross Hatch 32

pattern is a full field black & white pattern of crossing vertical and

horizontal lines dividing the screen into (32) sections in each direction. This pattern is

primarily used to check for color convergence and pincushion issues in projectors. There

are (2) variations: Normal (white lines, black field) and Inverse (black lines, white field).

22. DIAGONAL 1

The

Diagonal 1

pattern is a set of (3) diagonal colored lines (red,

white and blue) within a white square in the middle of the screen. This

pattern is used to check for distortion and alignment issues in the

center of the screen.

23. DIAGONAL 2

The

Diagonal 2

pattern is (2) diagonal lines that travel from the

corners to the exact center of the display. This can be used to check

for alignment and geometry issues, particularly with projectors. The

outer border of the screen also has a white outline to verify that the full

image is being displayed.

100%

75%

100%

75%

100%

75%

Содержание ANI-4KANA





































































Результаты поиска

Содержание ANI-4KANA

Отзывы:

Похожие инструкции для ANI-4KANA

Бренды по названию

Популярные бренды

A-Neu Video ANI-4KANA, Инструкция по эксплуатации

Результаты поиска

Содержание ANI-4KANA

Отзывы:

Похожие инструкции для ANI-4KANA

Бренды по названию

Популярные бренды