A-Neu Video ANI-4KANA страница 61 Скачать руководство пользователя

Страница: 61 / 68

anapat SOFTWARE

Output Resolution

(Analyzer Mode & Pattern Mode)

This tab provides control over the unit’s Output Resolutions and allows setting

“Favorite

Timings”

for quick selection. These functions are available for both Analyzer Mode and

Pattern Mode.

NOTE:

The

“Bypass”

output resolution only works in Analyzer mode. The image below

is from the ANI-4KANA of the unit. The list of available resolutions for the ANI-4KANAL is

more limited.

Figure 5: Output Resolution in Pattern Mode, ANI-4KANA

The output resolution that is currently in use is displayed near the top of the window.

Selecting a new resolution for output can be done in one of two ways. Click on a resolution

in the

“Favorite Timings”

list or find the resolution in the list on the left and double-click

the resolution name.

To add a resolution to the

“Favorite Timings”

list, find it in the full list on the left and

click its check box. To remove a resolution from the list, find it in the full list on the left and

uncheck the checkbox. To remove all resolutions from the

“Favorite Timings”

list, click

the

“Check None”

button.

NOTE:

Favorites are not permanently saved and will be reset to the defaults when the

software is closed.

When connected to the ANI-4KANAL in Analyzer Mode the available Output Resolution

choices are limited to 3 options: A pure Bypass mode, a mode that down-converts 4K

sources to 1080p and outputs as RGB (same frame rate as the source), and a mode

that down-converts 4K sources to 1080p and outputs as YCbCr (same frame rate as the

source).

Содержание ANI-4KANA





































































Результаты поиска

Содержание ANI-4KANA

Отзывы:

Похожие инструкции для ANI-4KANA

Бренды по названию

Популярные бренды

A-Neu Video ANI-4KANA, Инструкция по эксплуатации

Результаты поиска

Содержание ANI-4KANA

Отзывы:

Похожие инструкции для ANI-4KANA

Бренды по названию

Популярные бренды