A-Neu Video ANI-4KANA Скачать руководство пользователя

Страница: 15 / 68

RS-232 Protocol & Telnet Commands

RS-232 Protocol

SIGNAL GENERATOR

REMOTE CONTROL

PIN

ASSIGNMENT

PIN

ASSIGNMENT

TxD

RxD

TxD

GND

RS-232 & Telnet Commands

Before using the commands, please read the following:

SYNTAX

• All commands

MUST

start with the

“$”

character or the command will not be recognized

by the unit. Commands must end with a carriage return (0x0D). Use of a line feed (0x0A)

is optional. Commands are not case-sensitive.

PARAMETERS

• The characters

“[“ and “]”

are placed around descriptions of the variable parameters

where additional explanation was needed. Please type the selected parameter without

the contents inside the

“[“ and “]”

characters when entering the command.

RESPONSES

• The unit will respond to most commands with a repeat of the original command followed

by the specified parameters or requested information except where otherwise noted. If

an invalid command is entered the unit will respond with

“$err”

• All unit responses end with a carriage return (0x0D) + line feed (0x0A).

CAUTIONS

• Only one command may be processed at a time. Additional commands should not be

sent until the response from the previous command has been received.

Baud Rate: 115200bps

Data Bits: 8

Parity: None

Flow Control: None

Stop Bit: 1

Содержание ANI-4KANA





































































Результаты поиска

Содержание ANI-4KANA

Отзывы:

Похожие инструкции для ANI-4KANA

Бренды по названию

Популярные бренды

A-Neu Video ANI-4KANA, Инструкция по эксплуатации

Результаты поиска

Содержание ANI-4KANA

Отзывы:

Похожие инструкции для ANI-4KANA

Бренды по названию

Популярные бренды