A-Neu Video ANI-4KANA Скачать руководство пользователя

Страница: 11 / 68

OPERATION CONTROLS & FUNCTIONS

HDCP PATTERN:

Press to enable/disable the OSD display of the detected HDCP

version support and handshaking information between the sink and source. In Analyzer

mode the unit is the RX, in Pattern mode the unit is the TX. In Pattern mode, if HDCP

handshaking fails, an error message

“HDCP OUT FAIL”

will be displayed on the OSD.

HDCP ON/OFF:

Press to switch between supported HDCP versions or to disable

HDCP. Within Analyzer mode, OFF (LED=Off), HDCP 1.4 (LED=Red), and HDCP 1.4+2.2

(LED=Blue) modes are available for the input port. Within Pattern mode, OFF, HDCP 1.4,

and HDCP 2.2 modes are available for the output port.

COLOR SPACE:

Press repeatedly to switch between the available color space formats.

The button’s LED is colored to indicate the current color space: Red=RGB, Blue=YCbCr

4:4:4, Purple=YCbCr 4:2:0, Off=YCbCr 4:2:2.

DEEP COLOR:

Press repeatedly to switch between the available output color bit depth

options. The button’s LED is colored to indicate the current bit depth: OFF=8-bit, Red=10-

bit, Blue=12-bit.

OUTPUT FORMAT:

Press to switch between DVI (LED=Blue) and HDMI (LED=Red)

output formats. Press and hold the button for 2 seconds to disable/enable video output

completely. The button’s LED will turn off when output is disabled.

SIDE PANELS

AUDIO OUT:

Connects to powered speakers or an amplifier for stereo analog audio

output with a 3.5mm phone jack cable.

VGA OUT:

Connects to a VGA (RGBHV) monitor or display for analog video output.

HDMI OUT:

Connects to HDMI TVs, monitors or amplifiers for digital video and audio

output.

Содержание ANI-4KANA





































































Результаты поиска

Содержание ANI-4KANA

Отзывы:

Похожие инструкции для ANI-4KANA

Бренды по названию

Популярные бренды

A-Neu Video ANI-4KANA, Инструкция по эксплуатации

Результаты поиска

Содержание ANI-4KANA

Отзывы:

Похожие инструкции для ANI-4KANA

Бренды по названию

Популярные бренды