A-Neu Video ANI-4KANA Скачать руководство пользователя

Страница: 45 / 68

Test PATTERNS

13. COLORBAR DELAY

The

Colorbar Delay

pattern provides a sequence of standard 100%

color bars with a full set of smaller color squares within each bar. This

test is primarily to detect if any of the color components of the video

signal are delayed/skewed relative to each other. Pay close attention

to the left and right sides of the squares and look for a color shift. This

is a common problem when using extreme-length analog extension

products, or very long analog cables.

14. COLORBAR-H

The

Colorbar-H

pattern is a standard (white, yellow, cyan, green,

magenta, red, blue, black) 100% color bar pattern using horizontal

bars.

15. COLORBAR MOTION

The

Colorbar Motion

pattern is a standard (white, yellow, cyan, green,

magenta, red, blue, black) 100% color bar pattern using vertical bars

with a grey bar moving horizontally across it. There are 2 variations:

slow and fast motion of the grey bar.

16. COLORBAR S

The

Colorbar S

pattern is a standard SMPTE color bar pattern which

is used for rapid verification of signal color accuracy and for display

setup using the Blue-Only option on your display, if it has one.

17. COLORBAR SPLIT

The

Colorbar Split

pattern is a vertical color bar pattern with the

color bars split in the middle by large black and white sections. All

colors (white, yellow, cyan, green, magenta, red, blue) are at 100%

brightness.

18. COLORBAR-V (3 VARIATIONS)

The

Colorbar-V

pattern comes in (3) variations. The first is a standard (white, yellow,

cyan, green, magenta, red, blue, black) 100% color bar pattern using vertical bars. The

2nd variation has all bars at 75% brightness. The 3rd variation is split with the top half

being at 100% and the lower half being at 75% brightness.

Slow/Fast

Motion

100%

75%

100% & 75%

Содержание ANI-4KANA





































































Результаты поиска

Содержание ANI-4KANA

Отзывы:

Похожие инструкции для ANI-4KANA

Бренды по названию

Популярные бренды

A-Neu Video ANI-4KANA, Инструкция по эксплуатации

Результаты поиска

Содержание ANI-4KANA

Отзывы:

Похожие инструкции для ANI-4KANA

Бренды по названию

Популярные бренды