A-Neu Video ANI-4KANA страница 63 Скачать руководство пользователя

Страница: 63 / 68

anapat SOFTWARE

The pattern that is currently in use is displayed near the top of the window. Selecting a

new pattern for output can be done in one of two ways. Click on a pattern in the

“Favorite

Patterns”

list or find the pattern in the list on the left and double-click the resolution name.

Patterns with multiple versions or modes are marked with an

(*)

The additional versions

of the pattern are activated by re-selecting the pattern multiple times.

To add a pattern to the

“Favorite Patterns”

list, find it in the full list on the left and click its

check box. To remove a pattern from the list, find it in the full list on the left and uncheck

the checkbox. To remove all patterns from the

“Favorite Patterns”

list, click the

“Check

None”

button.

NOTE:

Favorites are not permanently saved and will be reset to the defaults when the

software is closed.

Control Panel

(Analyzer Mode & Pattern Mode)

This tab provides control over the unit’s additional features, functions and settings that

are not covered by the other tabs. The available controls change depending on the unit’s

current operational mode (Analyzer or Pattern), and which functions are appropriate based

on the unit’s current output resolution and pattern selection.

Figure 8: Control Panel in Analyzer Mode, ANI-4KANA

Содержание ANI-4KANA





































































Результаты поиска

Содержание ANI-4KANA

Отзывы:

Похожие инструкции для ANI-4KANA

Бренды по названию

Популярные бренды

A-Neu Video ANI-4KANA, Инструкция по эксплуатации

Результаты поиска

Содержание ANI-4KANA

Отзывы:

Похожие инструкции для ANI-4KANA

Бренды по названию

Популярные бренды