Chapter 8 Basic Setting
XS1920 Series User’s Guide
69
MAC Address
Learning
MAC address learning reduces outgoing traffic broadcasts. For MAC address learning to
occur on a port, the port must be active.
Aging Time
Enter a time from 10 to 1000000 seconds. This is how long all dynamically learned MAC
addresses remain in the MAC address table before they age out (and must be relearned).
ARP Aging Time
Aging Time
Enter a time from 60 to 1000000 seconds. This is how long dynamically learned ARP entries
remain in the ARP table before they age out (and must be relearned). The setting here
applies to ARP entries which are newly added in the ARP table after you click
Apply
.
GARP Timer: Switches join VLANs by making a declaration. A declaration is made by issuing a
Join
message
using GARP. Declarations are withdrawn by issuing a
Leave
message. A
Leave All
message terminates all
registrations. GARP timers set declaration timeout values. See the chapter on VLAN setup for more
background information.
Join Timer
Join Timer sets the duration of the Join Period timer for GVRP in milliseconds. Each port has
a
Join Period
timer. The allowed
Join Time
range is between 100 and 65535 milliseconds;
the default is 200 milliseconds. See the chapter on VLAN setup for more background
information.
Leave Timer
Leave Time sets the duration of the
Leave Period
timer for GVRP in milliseconds. Each port
has a single
Leave Period
timer. Leave Time must be two times larger than
Join Timer
;
the default is 600 milliseconds.
Leave All Timer
Leave All Timer sets the duration of the Leave All Period timer for GVRP in milliseconds.
Each port has a single Leave All Period timer. Leave All Timer must be larger than Leave
Timer.
Priority Queue Assignment
IEEE 802.1p defines up to eight separate traffic types by inserting a tag into a MAC-layer frame that contains
bits to define class of service. Frames without an explicit priority tag are given the default priority of the
ingress port. Use the next fields to configure the priority level-to-physical queue mapping.
The Switch has eight physical queues that you can map to the 8 priority levels. On the Switch, traffic assigned
to higher index queues gets through faster while traffic in lower index queues is dropped if the network is
congested.
Priority Level (The following descriptions are based on the traffic types defined in the IEEE 802.1d standard
(which incorporates the 802.1p).
Level 7
Typically used for network control traffic such as router configuration messages.
Level 6
Typically used for voice traffic that is especially sensitive to jitter (jitter is the variations in
delay).
Level 5
Typically used for video that consumes high bandwidth and is sensitive to jitter.
Level 4
Typically used for controlled load, latency-sensitive traffic such as SNA (Systems Network
Architecture) transactions.
Level 3
Typically used for “excellent effort” or better than best effort and would include important
business traffic that can tolerate some delay.
Level 2
This is for “spare bandwidth”.
Level 1
This is typically used for non-critical “background” traffic such as bulk transfers that are
allowed but that should not affect other applications and users.
Level 0
Typically used for best-effort traffic.
Apply
Click
Apply
to save your changes to the Switch’s run-time memory. The Switch loses these
changes if it is turned off or loses power, so use the
Save
link on the top navigation panel to
save your changes to the non-volatile memory when you are done configuring.
Cancel
Click
Cancel
to reset the fields.
Table 13
Basic Setting > Switch Setup (continued)
LABEL
DESCRIPTION
Summary of Contents for XS1920 Series
