AAM1212-51/53 Series User’s Guide
420
Chapter 55 Troubleshooting
55.15.1 Resetting the Defaults Via Command
If you know the password, you can reload the factory-default configuration file via Command
Line Interface (CLI) command. Use the following procedure.
1
Connect to the console port using a computer with terminal emulation software. See
for details.
2
Enter your password.
3
Type
config restore
.
4
Type
y
at the question “Do you want to restore default ROM file(y/n)?”
5
The AAM1212 restarts.
The AAM1212 is now reinitialized with a default configuration file including the default user
name of “admin” and the default password of “1234”.
55.15.2 Uploading the Default Configuration File
If you forget your password or cannot access the AAM1212, you will need to reload the
factory-default configuration file. Uploading the factory-default configuration file replaces the
current configuration file with the factory-default configuration file. This means that you will
lose all previous configurations and the speed of the console port will be reset to the default of
9600 bps with 8 data bit, no parity, one stop bit and flow control set to none. The password
will also be reset to “1234” and the IP address to 192.168.1.1.
Note:
Uploading the factory default configuration file erases the AAM1212’s entire
configuration.
Obtain the default configuration file, unzip it and save it in a folder. Use a console cable to
connect a computer with terminal emulation software to the AAM1212’s console port. Turn
the AAM1212 off and then on to begin a session. When you turn on the AAM1212 again you
will see the initial screen. When you see the message
Press any key to enter Debug
Mode within 3 seconds
press any key to enter debug mode.
To upload the configuration file, do the following:
1
Type
atlc
after the
Enter Debug
Mode message.
Figure 297
Resetting the Switch Via Command
ras> config restore
System will reboot automatically after restoring default configuration.
Do you want to proceed(y/n)? >
restoring configuration...
saving configuration to flash...
Summary of Contents for AAM1212-51
