Zurich ZR13s, Owner'S Manual

Page: 34 / 52

For technical questions, please call 1-888-866-5797
32
About the Scan Tool
DIS PL AY FUNC TIONS
3
5. M (Menu) button – W hen pre sse d, d isp lay s th e M ain Men u.
6. LD button – When pressed while linked to a vehicle, places the
Scan To ol in Live Data mode.
7. UP butto n – When in ME NU mode, scrolls UP through the
menu optio ns. When LINKED to a vehic le, scrolls UP thro ugh the
current disp lay screen to disp lay any addit iona l data.
8. ENTER button
- When in Menu mode, confirms the selected
option or value.
9. DOWN button - W hen in M EN U m ode , s cro lls do wn thr oug h the
menu options. When LI NKED to a veh icl e, scr olls do wn throu gh the
current disp lay screen to disp lay any addit iona l data.
10.GR EEN L ED - Indicates tha t all eng ine s ystems are runnin g
normally (all Monitors on the vehi cle are a ctive and performing their
diagnostic testing, and no DTCs are present).
11.YEL LOW LE D - Indicates there is a possible problem. A “Pe nding”
DTC is pres ent and/or some of the vehicle's em ission mon itors have
not run their dia gnostic testin g.
12.RE D L ED - Indicates there is a problem in one or more o f th e
vehicle's system s. The red LED is al so used to show that DT C(s)
are present. DTCs are show n on the Scan Tool’s LCD display. In
this case, the Malfunctio n Indicator (“Check Eng ine”) lamp on the
vehicle 's ins tru men t p ane l will light steady on.
13.Di splay
- D isp lay s te st r esu lts , S can T ool fun ctio ns and Mon ito r s tat us
info rm atio n. S ee DIS PLA Y F UN CT IO NS , b elo w, fo r d eta ils .
14.CABLE - C onn ect s th e S can Too l to the ve hic le' s D ata Li nk C onn ect or
(DLC).
DISPLAY FUNC TIONS
Figure 2. Display Functions
See F igure 2 for the locations of items 1 through 15, below.
1. I/M M ONIT OR S TA TU S f ield - Id ent ifie s th e I/ M Monitor status area.
4
3
2
5
7
6
1 14
10
11
12
8
9
13
15
SYSTEM TEST MENU
Additional Tests
SYSTEM TEST MENU
32
6. When you have finished viewing test data for all desired sensors,
select
Back , then press ENTER to return to the System Test
menu; or, press M to return to the Main Menu.
OBD Monitor Test
The OBD Monitor Test function retrieves and displays test results for
emission-related powertrain components and systems that are not
continuously monitored. The tests available are determined by the
vehicle manufacturer.
The Scan Tool does not perform the OBD monitor test, but
retrieves results from the most recently performed tests from
the on-board computer’s memory. You may retrieve OBD
monitor test results for only one test at any given time.
1. From the System Test menu, select
OBD Monitor Test , then press ENTER
.
2. A “One moment please. . .” message
displays, followed by the Select Test
screen. (Refer to the vehicle’s service
repair manual for information related to
non-continuous tests.)
If OBD monitor test data is not presently stored in the vehicle’s
computer, an advisory message displays. Press
M to return to
the Main Menu.
If OBD monitor tests are not supported by the vehicle under test,
an advisory message displays. Press
M to return to the Main
Menu.
3. Use the UP and DOWN buttons,
as necessary, to highlight the desired test,
then press the
ENTER button.
„
Test ID number
„
Module ID number
„
Component ID number
„
Min or Max test limit (Only one test limit, either Min or Max , is
shown for any given test.)
„
Test Value and status
Status is calculated by the Scan Tool by comparing the Test
Value against the displayed test limit (either Min or Max ).
Status is shown as either Low , High or OK .
4. When you have finished viewing the retrieved test data, select Back
on the Select Test screen, then press ENTER to return to the
System Test menu; or, press M to return to the Main Menu.