Zurich ZR13s, Owner'S Manual

Page: 40 / 52

For technical questions, please call 1-888-866-5797
38
About the Scan Tool
DIS PL AY FUNC TIONS
3
5. M (Menu) button – W hen pre sse d, d isp lay s th e M ain Men u.
6. LD button – When pressed while linked to a vehicle, places the
Scan To ol in Live Data mode.
7. UP butto n – When in ME NU mode, scrolls UP through the
menu optio ns. When LINKED to a vehic le, scrolls UP thro ugh the
current disp lay screen to disp lay any addit iona l data.
8. ENTER button
- When in Menu mode, confirms the selected
option or value.
9. DOWN button - W hen in M EN U m ode , s cro lls do wn thr oug h the
menu options. When LI NKED to a veh icl e, scr olls do wn throu gh the
current disp lay screen to disp lay any addit iona l data.
10.GR EEN L ED - Indicates tha t all eng ine s ystems are runnin g
normally (all Monitors on the vehi cle are a ctive and performing their
diagnostic testing, and no DTCs are present).
11.YEL LOW LE D - Indicates there is a possible problem. A “Pe nding”
DTC is pres ent and/or some of the vehicle's em ission mon itors have
not run their dia gnostic testin g.
12.RE D L ED - Indicates there is a problem in one or more o f th e
vehicle's system s. The red LED is al so used to show that DT C(s)
are present. DTCs are show n on the Scan Tool’s LCD display. In
this case, the Malfunctio n Indicator (“Check Eng ine”) lamp on the
vehicle 's ins tru men t p ane l will light steady on.
13.Di splay
- D isp lay s te st r esu lts , S can T ool fun ctio ns and Mon ito r s tat us
info rm atio n. S ee DIS PLA Y F UN CT IO NS , b elo w, fo r d eta ils .
14.CABLE - C onn ect s th e S can Too l to the ve hic le' s D ata Li nk C onn ect or
(DLC).
DISPLAY FUNC TIONS
Figure 2. Display Functions
See F igure 2 for the locations of items 1 through 15, below.
1. I/M M ONIT OR S TA TU S f ield - Id ent ifie s th e I/ M Monitor status area.
4
3
2
5
7
6
1 14
10
11
12
8
9
13
15
BATTERY/ALTERNATOR TEST
Additional Tests
BATTERY/ALTERNATOR TEST
38
3. Select Alternator Test , then press ENTER .
„
An “instructional” message shows.
4. Start and warm the engine to normal operating temperature. Turn on
the headlights. Press
ENTER to continue.
„
An “instructional” message shows.
5. Press the accelerator pedal to raise engine speed to 2000 RPM,
and maintain the engine speed.
„
When engine speed is within the required range, the alternator
test begins. A progress screen shows.
„
When the “countdown” timer expires, an “instructional” message
shows.
6. Turn the vehicle’s headlights off, and return the engine to idle speed.
„
A “One moment please…” message
displays while the test results are
retrieved.
7. When the alternator check is complete,
a results screen shows charging system
voltage and indicates whether or not the
charging system is within acceptable
limits. The System Status LEDs provide
a PASS/FAIL indication, as follows:
„
Green = System within limits
„
Yellow = Over charging or under
charging
„
Red = Excessive over charging or
under charging
„
If the alternator voltage is less than
9 V, the red, yellow and green
SYSTEM STATUS LEDs will flash
on and off.
8. Press M to return to the Main Menu.
To perform a hybrid/EV battery system check:
1. Press M and release.
„
The Main Menu displays.
2. Select Battery/Alternator Test , then
press ENTER .
„
The Battery/Alternator Test Menu
displays.
3. Select Hybrid/EV Battery Test , then
press ENTER .