Zurich ZR13s, Owner'S Manual

Page: 28 / 52

For technical questions, please call 1-888-866-5797
26
About the Scan Tool
DIS PL AY FUNC TIONS
3
5. M (Menu) button – W hen pre sse d, d isp lay s th e M ain Men u.
6. LD button – When pressed while linked to a vehicle, places the
Scan To ol in Live Data mode.
7. UP butto n – When in ME NU mode, scrolls UP through the
menu optio ns. When LINKED to a vehic le, scrolls UP thro ugh the
current disp lay screen to disp lay any addit iona l data.
8. ENTER button
- When in Menu mode, confirms the selected
option or value.
9. DOWN button - W hen in M EN U m ode , s cro lls do wn thr oug h the
menu options. When LI NKED to a veh icl e, scr olls do wn throu gh the
current disp lay screen to disp lay any addit iona l data.
10.GR EEN L ED - Indicates tha t all eng ine s ystems are runnin g
normally (all Monitors on the vehi cle are a ctive and performing their
diagnostic testing, and no DTCs are present).
11.YEL LOW LE D - Indicates there is a possible problem. A “Pe nding”
DTC is pres ent and/or some of the vehicle's em ission mon itors have
not run their dia gnostic testin g.
12.RE D L ED - Indicates there is a problem in one or more o f th e
vehicle's system s. The red LED is al so used to show that DT C(s)
are present. DTCs are show n on the Scan Tool’s LCD display. In
this case, the Malfunctio n Indicator (“Check Eng ine”) lamp on the
vehicle 's ins tru men t p ane l will light steady on.
13.Di splay
- D isp lay s te st r esu lts , S can T ool fun ctio ns and Mon ito r s tat us
info rm atio n. S ee DIS PLA Y F UN CT IO NS , b elo w, fo r d eta ils .
14.CABLE - C onn ect s th e S can Too l to the ve hic le' s D ata Li nk C onn ect or
(DLC).
DISPLAY FUNC TIONS
Figure 2. Display Functions
See F igure 2 for the locations of items 1 through 15, below.
1. I/M M ONIT OR S TA TU S f ield - Id ent ifie s th e I/ M Monitor status area.
4
3
2
5
7
6
1 14
10
11
12
8
9
13
15
RECORDING (CAPTURING) LIVE DATA
Live Data Mode
RECORDING (CAPTURING) LIVE DATA
26
Record by DTC Trigger
This function automatically records Live Data information when a DTC
sets and saves it in the Scan Tool’s memory. The recorded data can be
a valuable troubleshooting aid, particularly if you are experiencing a fault
that is causing a DTC to set. The Scan Tool can record approximately
100 frames of Live Data.
1. With the Scan Tool in Live Data mode (see VIEWING LIVE DATA
on page 23), press and hold
LD until the Live Data Menu displays,
then release.
2. Select Record Live Data , then press ENTER .
„
The Record Live Data Menu displays.
„
If the Scan Tool fails to establish communication with the vehicle,
a “Communication Error” message displays.
- Ensure your vehicle is OBD2 compliant.
- Verify the connection at the DLC, and verify the ignition is ON.
- Turn the ignition OFF, wait 5 seconds, then back ON to reset
the computer.
- Press POWER/LINK to continue.
3. Select Record by DTC Trigger , then press ENTER .
„
The Select PIDs to Record screen displays.
4. Press UP and DOWN to scroll
through the available PIDs. When a PID
you wish to record is highlighted, press
ENTER (a “checkmark” shows to
confirm your selection). Repeat until
only the PIDs you want to record have
all been selected.
„
To deselect a PID, highlight the PID,
then press ENTER . The check-
mark is removed.
To record all PIDs, select Record All PIDs , the press
LD to continue.
5. When you are finished making your selections, press LD to continue.
„
If DTCs are presently stored in the
vehicle’s computer, an advisory
message displays. Select
Erase
DTCs , then press ENTER . A
“One moment please…” message
displays while DTCs are erased
from the vehicle’s computer.
„
If the erase was not successful, an
advisory message displays.