Zurich ZR13s, Owner'S Manual

Page: 30 / 52

For technical questions, please call 1-888-866-5797
28
About the Scan Tool
DIS PL AY FUNC TIONS
3
5. M (Menu) button – W hen pre sse d, d isp lay s th e M ain Men u.
6. LD button – When pressed while linked to a vehicle, places the
Scan To ol in Live Data mode.
7. UP butto n – When in ME NU mode, scrolls UP through the
menu optio ns. When LINKED to a vehic le, scrolls UP thro ugh the
current disp lay screen to disp lay any addit iona l data.
8. ENTER button
- When in Menu mode, confirms the selected
option or value.
9. DOWN button - W hen in M EN U m ode , s cro lls do wn thr oug h the
menu options. When LI NKED to a veh icl e, scr olls do wn throu gh the
current disp lay screen to disp lay any addit iona l data.
10.GR EEN L ED - Indicates tha t all eng ine s ystems are runnin g
normally (all Monitors on the vehi cle are a ctive and performing their
diagnostic testing, and no DTCs are present).
11.YEL LOW LE D - Indicates there is a possible problem. A “Pe nding”
DTC is pres ent and/or some of the vehicle's em ission mon itors have
not run their dia gnostic testin g.
12.RE D L ED - Indicates there is a problem in one or more o f th e
vehicle's system s. The red LED is al so used to show that DT C(s)
are present. DTCs are show n on the Scan Tool’s LCD display. In
this case, the Malfunctio n Indicator (“Check Eng ine”) lamp on the
vehicle 's ins tru men t p ane l will light steady on.
13.Di splay
- D isp lay s te st r esu lts , S can T ool fun ctio ns and Mon ito r s tat us
info rm atio n. S ee DIS PLA Y F UN CT IO NS , b elo w, fo r d eta ils .
14.CABLE - C onn ect s th e S can Too l to the ve hic le' s D ata Li nk C onn ect or
(DLC).
DISPLAY FUNC TIONS
Figure 2. Display Functions
See F igure 2 for the locations of items 1 through 15, below.
1. I/M M ONIT OR S TA TU S f ield - Id ent ifie s th e I/ M Monitor status area.
4
3
2
5
7
6
1 14
10
11
12
8
9
13
15
LIVE DATA PLAYBACK
Live Data Mode
LIVE DATA PLAYBACK
28
„
The Select PIDs to Record screen
displays.
4. Press UP and DOWN to scroll
through the available PIDs. When a PID
you wish to record is highlighted, press
ENTER (a “checkmark” shows to
confirm your selection). Repeat until
only the PIDs you want to record have
all been selected.
„
To deselect a PID, highlight the PID, then press ENTER . The
checkmark is removed.
To record all PIDs, select Record All PIDs , the press
LD to continue.
5. When you are finished making your selections, press LD to continue.
„
The Record Live Data screen
displays.
„
Highlight Start Recording . Put the
engine in the operating condition
where the problem manifests itself.
- If necessary, drive the vehicle
until you reach the vehicle speed
at which the problem occurs.
6. When the problem occurs, press and
release
LD .
„
A progress message shows on the display.
- You can stop and save recorded Live Data at any time by
pressing ENTER .
„
When recording is complete, a confirmation screen displays.
Select
Yes and press ENTER to playback Live Data (see
LIVE DATA PLAYBACK on page 28 for details) or select No and
press ENTER to return to the Live Data menu, as desired.
„
If recording was not successful, an advisory message displays.
Press
ENTER to return to the Record Live Data menu.
LIVE DATA PLAYBACK
Once Live Data has been recorded, it is saved in the Scan Tool's
memory. You can view recorded Live Data immediately after recording
by selecting Yes from the Record Live Data confirmation screen (see
RECORDING (CAPTURING) LIVE DATA on page 25 for more
information), or you can view it later using the "Playback" function.
1. With the Scan Tool connected to the vehicle and in Live Data mode
(see VIEWING LIVE DATA on page 23), press and hold
LD until the
Live Data Menu displays, then release.
2. Select Playback Live Data , then press the ENTER button.
„
The Playback Live Data menu displays.