Zurich ZR13s, Owner'S Manual

Page: 14 / 52

For technical questions, please call 1-888-866-5797
12
About the Scan Tool
DIS PL AY FUNC TIONS
3
5. M (Menu) button – W hen pre sse d, d isp lay s th e M ain Men u.
6. LD button – When pressed while linked to a vehicle, places the
Scan To ol in Live Data mode.
7. UP butto n – When in ME NU mode, scrolls UP through the
menu optio ns. When LINKED to a vehic le, scrolls UP thro ugh the
current disp lay screen to disp lay any addit iona l data.
8. ENTER button
- When in Menu mode, confirms the selected
option or value.
9. DOWN button - W hen in M EN U m ode , s cro lls do wn thr oug h the
menu options. When LI NKED to a veh icl e, scr olls do wn throu gh the
current disp lay screen to disp lay any addit iona l data.
10.GR EEN L ED - Indicates tha t all eng ine s ystems are runnin g
normally (all Monitors on the vehi cle are a ctive and performing their
diagnostic testing, and no DTCs are present).
11.YEL LOW LE D - Indicates there is a possible problem. A “Pe nding”
DTC is pres ent and/or some of the vehicle's em ission mon itors have
not run their dia gnostic testin g.
12.RE D L ED - Indicates there is a problem in one or more o f th e
vehicle's system s. The red LED is al so used to show that DT C(s)
are present. DTCs are show n on the Scan Tool’s LCD display. In
this case, the Malfunctio n Indicator (“Check Eng ine”) lamp on the
vehicle 's ins tru men t p ane l will light steady on.
13.Di splay
- D isp lay s te st r esu lts , S can T ool fun ctio ns and Mon ito r s tat us
info rm atio n. S ee DIS PLA Y F UN CT IO NS , b elo w, fo r d eta ils .
14.CABLE - C onn ect s th e S can Too l to the ve hic le' s D ata Li nk C onn ect or
(DLC).
DISPLAY FUNC TIONS
Figure 2. Display Functions
See F igure 2 for the locations of items 1 through 15, below.
1. I/M M ONIT OR S TA TU S f ield - Id ent ifie s th e I/ M Monitor status area.
4
3
2
5
7
6
1 14
10
11
12
8
9
13
15
VIEWING OEM ENHANCED DTCs
Using the Scan Tool
VIEWING OEM ENHANCED DTCs (Ford/Mazda only)
12
2. Refer to DISPLAY FUNCTIONS on page 2 for a description of LCD
display elements.
If the definition for the currently
displayed code is not available,
an advisory message shows.
I/M MONITOR STATUS icons
are not displayed when
viewing enhanced DTCs.
In the case of long code
definitions, a small arrow is
shown in the upper/lower
right-hand corner of the code display area to indicate the
presence of additional information.
„
If no codes are present, the message “No OEM Enhanced DTC’s
are presently stored in the vehicle’s computer” shows. Press
SYSTEM MENU to return to the System Menu.
3. If more than one code was retrieved press DTC/FF , as necessary,
to display additional codes one at a time.
„
Whenever the Scroll function is used to view additional codes,
the Scan Tool’s communication link with the vehicle’s computer
disconnects.
To re-establish communication, press
POWER/LINK again.
4. When the last retrieved DTC has been displayed and DTC/FF is
pressed, the Scan Tool returns to the “Priority” Code.
„
To exit the enhanced mode, press SYSTEM MENU to return
to the System Menu. Select Global OBD , then press ENTER
to return to the Global OBD2 mode.
VIEWING OEM ENHANCED DTCs (Ford/Mazda only)
Mazda Enhanced DTCs are available for Mazda-branded
Ford vehicles only .
When Ford OEM Enhanced is chosen from
the System Menu, the Ford Enhanced
menu displays. You may view OEM DTCs
for either the “Continuous Memory Test”,
“KOEO (Key On Engine Off) Test” or
“KOER (Key On Engine Running) Test.”
1. Select the desired option, then press
ENTER .
„
If KOER is selected, an advisory message shows.
- Start and warm the engine to normal operating temperature,
then press ENTER . Proceed to step 3 .
2. If KOEO or Continuous Memory is selected, an “instructional”
message shows.