ZOTYE JNJ7155 Quick Start Manual Download Page 134 | Manualshive

Page: 134 / 290

background image

132

Seat

Seat

Head restraint

Correct adjustment of headrest is key to drop the accidents and to
protect drivers and passengers.

The headrest should be so adjusted that your center of rear head could
be at the center of headrest and that the upper edge of headrest could
be as high as the head top (or as much as possible).

Otherwise, it is apt to cause personal injury in case of accident.

Adjustment of front seat headrests

While pressing the lock button at the top of seat back, move the
headrest longitudinally to the proper height. With the lock button
released, make sure the headrest is locked in place.

«
...
132
133
134
135
136
...
»

Summary of Contents for JNJ7155



































































































































































































































































































Reviews:

No comments

Related manuals for JNJ7155

Brand: Oldsmobile Pages: 360

Brand: Warrior Winches Pages: 17

Brand: APEXi Pages: 18

Brand: Prorack Pages: 15

Brand: Phonocar Pages: 6

Brand: Webasto Pages: 18

Truck Training Model

Brand: WABCO Pages: 56

THERAPEDIC 2000

Brand: Columbia Pages: 14

Brand: Edelbrock Pages: 2

Brand: Mercedes-Benz Pages: 93

Brand: Ultraplast Pages: 5

Brand: Macally Pages: 10

Brand: Volkswagen Pages: 188

Brand: TigerTough Pages: 7

Brand: Chevrolet Pages: 324

Brand: AutoMaxi Pages: 2

Brand: NavInc Pages: 5

ETSS100CBKFV-BP

Brand: Soundoff Signal Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands