ZOTYE JNJ7155 Quick Start Manual Download Page 278

Page: 278 / 290

276

Technical Data

Total weight and other design parameters

Model

Item

JNJ7155

JNJ7155T

JNJ7155QT

JNJ7155Q

Maximum gross mass (kg)

1720

1745

1795

1770

Curb mass (kg)

1345

1370

1420

1395

Axle load (kg)

Front axle load

893

925

962

940

Rear axle load

827

820

833

830

Rated number of passengers (people)

Maximum gradeability %

Minimum turning diameter (m)

10.3

Minimum ground clearance (mm)

180 (curb) /161 (full loaded)

Approach angle (°)

19.5 (curb) /18.9 (full loaded)

Departure angle (°)

30.3 (curb) /23.7 (full loaded)

Capacity of fuel tank (L)

48±2

Comprehensive fuel consumption (L/100km)

6.7

7.2

7.1

Description!

Meaning of vehicle model code in parameter sheet of technical performance: JNJ7155 (1.5L 5MT)/JNJ7155Q (1.5L CVT)/JNJ7155QT(1.5T
CVT)/JNJ7155T(1.5T5MT).

Summary of Contents for JNJ7155



































































































































































































































































































Search results

Summary of Contents for JNJ7155

Reviews:

Related manuals for JNJ7155

Brands by name

Popular brands

ZOTYE JNJ7155, Quick Start Manual

Search results

Summary of Contents for JNJ7155

Reviews:

Related manuals for JNJ7155

Brands by name

Popular brands