manualshive.com logo in svg

ZOTYE JNJ7155, Quick Start Manual

The ZOTYE JNJ7155 is a cutting-edge vehicle designed for adventure seekers. With our Quick Start Manual, you can easily get acquainted with all its features, ensuring a hassle-free experience from the get-go. Download the manual for free from manualshive.com now and unleash the full potential of your ZOTYE JNJ7155.

Share
Download
background image

 

 

Handling of accidents 

253 

Safety 

Handling 

Driving Guide 

Operating Guide 

DIY 

Technical Data 

Index 

 

Replacement of wheels and installation of spare wheel 

 

–  Before  installation  of  spare  tire,  install  the  wheel  nuts  and 

pre-tighten  them  with  a  wheel  wrench  until  the  wheel  is  reliably 
secured. 

–  Rotate the jack crank counterclockwise to lower the car. 

–  Use the wheel wrench to screw down the wheel nuts crosswise as 

per  the  sequence  indicated  by  the  number  shown  on  the  above 
diagram. 

–  Lower the jack to the bottom, and take out the jack under the car. 

 

 

Warning!

 

Oil or grease must not be used on the bolt or nut; otherwise, the nut 
may fall, resulting in traffic accident because of falling of wheel. 

Inspection after tire replacement 

●  Check the tire pressure after replacement. 
●  Adjust  the  tire  pressure  to  the  stipulated  value.  If  the  actual 

pressure is below the stipulated value, drive the vehicle slowly to 
the service station nearby for air filling, and increase the pressure 
to the correct value. 

●  Install  the  valve  cap  to  prevent  the  dust  and  moisture  from 

entering the valve; the entering of dust may cause air leaking, and 
thus  result  in  accident.  The  valve  cap  that  is  missing  shall  be 
refitted as soon as possible. 

●  All  the  tools,  warning  triangle  and  flat  tire  shall  be  arranged 

properly. 

Warning!

 

●  Before  driving,  make  sure  that  all  the  tools,  warning  triangle 

and  flat  tire  are  fastened  at  the  storage  position  for  fear  of 
personal injury in case of emergency braking or collision. 

●  The  spare  tire  can  only  be  used  for  a  short  time,  and  is 

unsuitable for expressway. 

 

Summary of Contents for JNJ7155



































































































































































































































































































Reviews:

No comments

Related manuals for JNJ7155

Laser 4832 Manual preview
4832
Brand: Laser Pages: 8
Lange Originals HOIST-A-TOP JL CRANK Installation Instructions Manual preview
HOIST-A-TOP JL CRANK
Brand: Lange Originals Pages: 13
RAM 2500 2020 Quick Reference Manual preview
2500 2020
Brand: RAM Pages: 20
Whispbar K611W Fitting Instructions Manual preview
K611W
Brand: Whispbar Pages: 77
Lit Lightz RGBW Rock Lights Setup Manual preview
RGBW Rock Lights
Brand: Lit Lightz Pages: 3
Daesung HM-TX-315 User Manual preview
HM-TX-315
Brand: Daesung Pages: 9
Pontiac 2010 Vibe Owner'S Manual preview
2010 Vibe
Brand: Pontiac Pages: 318
Cadillac 2000 DeVille Service Manual Addendum preview
2000 DeVille
Brand: Cadillac Pages: 19
Havis-Shields Telescoping Computer Base C-TCB-34 Install Instructions preview
Telescoping Computer Base C-TCB-34
Brand: Havis-Shields Pages: 1
PEUGEOT 106 2001 Owner'S Manual preview
106 2001
Brand: PEUGEOT Pages: 107
Jaeger 21260514J Fitting Instructions Manual preview
21260514J
Brand: Jaeger Pages: 11
ATS 664-0030 Installation And Operating Manual preview
664-0030
Brand: ATS Pages: 12
Poison Spyder TrailGate TJ Installation Instructions preview
TrailGate TJ
Brand: Poison Spyder Pages: 5
JBA 1528S Installation Instructions And Warranty Information preview
1528S
Brand: JBA Pages: 5
Edelbrock Turbocharger 15012 Installation Instructions preview
Turbocharger 15012
Brand: Edelbrock Pages: 1
GMC Yukon XL Denali 2015 Owner'S Manual preview
Yukon XL Denali 2015
Brand: GMC Pages: 439
BMW 325i 1991 Electrical Troubleshooting Manual preview
325i 1991
Brand: BMW Pages: 64
Safe Fleet RVS-218629 Instruction Manual preview
RVS-218629
Brand: Safe Fleet Pages: 28

Brands by name

Popular brands

Load more brands