ZOTYE JNJ7155 Quick Start Manual Download Page 137

Page: 137 / 290

Seat

135

Safety

Handling

Driving Guide

Operating Guide

DIY

Technical Data

Index

Front seat

* Electrical adjustment of seat

1. Switch for adjustment of seat

2. Switch for adjustment of backrest angle

Front and back adjustment of seat

Forward push the switch

①

, to move the seat forwards.

Backward push the switch

①

, to move the seat backwards.

Adjustment of cushion height

Upward press the switch

①

, lifting the cushion.

Downward press the switch

①

, lowering the cushion.

Backrest angle adjustment

Forward push the switch

②

, to tilt the backrest forwards.

Backward push the switch

②

, to tilt the backrest backwards.

Summary of Contents for JNJ7155



































































































































































































































































































Search results

Summary of Contents for JNJ7155

Reviews:

Related manuals for JNJ7155

Brands by name

Popular brands

ZOTYE JNJ7155, Quick Start Manual

Search results

Summary of Contents for JNJ7155

Reviews:

Related manuals for JNJ7155

Brands by name

Popular brands