4、REAR WHELL COMPONENT
25
CHK
ADJ
NO.
PART NO.
PART NAME
QTY
CAUTION
1
1252200-016093 250Rear fork shaft
∅
14×310
（
Dacro
）
1
2
1251300-059093 125Rear fork shaft nutM14×1.5
（
Dacro
）
1
3
1251100-102000 Non-standard bolt M6×16
（
stainless steel
）
3
4
1224200-003000 ZT310
－
ZRear disc brake pipe clamp
1
1080200-032000 ZT250
－
R 114 Chain
（
CHOHO520HX
）
1080200-055000 ZT250
－
R 114 Chain
（
CHOHO520HX/ open type
）
【
1
】
6
1104100-005000 ZT250
－
Soil seal TC20×26×4
4
After sales only
7
1094100-001000 ZT250
－
S Needle bearing
（
HK2016)
4
After sales only
8
1274100-009000 ZT250
－
S Rear fork bushing
2
4024100-024000 ZT250Aluminum alloy rear fork assembly
4074200-005051
ZT250 dark gray aluminum alloy rear flat fork assembly
10
1244100-066000 ZT310
－
Z Rear fork wear block
1
11
1274100-057095
Flanging bushingφ6.2×φ8.4×3.5
＋
φ14×1.5
2
12
1251300-050000
ZT310
－
ZChain adjuster nut M10
（
304stainless steel
）
2
13
1251100-105000 ZT310
－
ZChain adjuster bolt M10×70
2
14
1251500-097000
Non-standard flat mats φ6.5×φ22×1.5
1
Old rear fork anti-bearing
block
9
1
Improvements rear fork
anti-bearing block
Old rear fork anti-bearing
block
Improvements rear fork
anti-bearing block
Fig.5 REAR WHELL
COMPONENT
Rear swinging arm component
5
1
PROCEDURE:
●
Rear fork assembly
Pull off the disc brake oil pipe
①
and wheel speed sensor
②
from the disc brake oil pipe clamp(4),loosen the bolt(3) and take
off the disc brake oil pipe clamp.
The rear disc brake caliper is placed well and cannot be higher than the disc brake oil cup,as shown in left figure.
One person fastens the head of the rear fork shaft with sleeve, and the other person remove the nut(2)with it.
One person holds the rear fork assembly and the other person removes the rear fork shaft(1) with suitable tool and then
remove the rear fork assembly.
●
Rear fork rear-resistant block
Remove the bolt(3),flanging bushing(1) with inner hexagon tool, and then remove the wear-resistent block.
Remove the chain adjuster bolt(12) and nut(13) with the open end wrench.
Put the rear fork bushing (8) inward and remove it.
Oil seal (6) and needle bearing (7) are used for interference compression.
Please ensure that you have the ability to disassemble and disassemble.
CAUTION:
●
The rear disc brake caliper must not be higher than the disc brake oil cup, otherwise the brake will become soft or fail due
to air entering the pipeline. Because the brake line requires extremely high vacuum, it is necessary to ensure sufficient
capacity for repair and disassembly.
●【
1
】
The open type is convenient for replacing the chain after sale, and the original vehicle has no opening. A special
chain installation tool is required, and the tool must be purchased by yourself.
●
If your motocycle manufactured before Set.2,2019,it's need to be accompained by the purchase of non-standard flat mats
⒀
when replace Rear fork anti-bearing block
⑽
.
