background image

 

General warning and safety instructions 

000000-1272-175-GA-GB-060613 

18 

Laser safety goggles 

WARNING - RISK OF LASER RADIATION 
All persons present in the laser hazard area during laser operation must 

wear laser safety goggles. The patient's eye which is not being treated must 

also be properly protected. 
Exception: 

The physician does not require laser safety goggles when observing the 
target area through 

 

a surgical microscope equipped with a 532 nm physician's safety filter 

 

a laser slit lamp supplied by Carl Zeiss Meditec 

 

a diagnostic slit lamp as described in the user manual in conjunction  
with VISULINK 532/U or 

 

the LIO Trion/532s laser indirect ophthalmoscope 

The institution operating the device is responsible for providing proper laser 

safety goggles. The safety goggles must be approved for the wavelength of 
the laser and for the type and intensity of the laser radiation (in Europe, in 

compliance with DIN EN 207).

 

 

 

VISULAS YAG III: YAG laser safety goggles 

 

VISULAS 532s: Laser safety goggles Argon/532 

 

VISULAS Trion: Laser safety goggles 532/561, laser safety goggles 659 

 

 

The laser hazard area is the area in which the maximum permissible 

exposure (MPE) may be exceeded. This includes areas into which 

the laser beam may unintentionally be deflected by a reflecting 

surface. 

 

 

 

 

 

 

 

 

Summary of Contents for VISULAS YAG III































































































































Reviews: