manualshive.com logo in svg

YASKAWA SI-EN3, Technical Manual, Page: 59 / 69

Share
Download
YASKAWA SI-EN3 Technical Manual Download Page 59

12  Web Interface

YASKAWA ELECTRIC

 SIEP C730600 92A YASKAWA AC Drive Option SI-EN3 Technical Manual

 59

Table 14  Network Monitor Explanations

Note:

Network monitors are reset when the power supply is cycled.

Network Monitor

Explanation

Msg Tx OK

Cumulative number of messages transmit successfully from the option.

Msg Rx OK

Cumulative number of messages received successfully to the option.

Current Connections

Current number of open connections.

Msg Tx Dropped

Cumulative number of messages dropped due to output network buffer being full and unable to hold the new 
message.

Msg Rx Dropped

Cumulative number of messages dropped due to input network buffer being full and unable to hold the new 
message.

Collisions

Cumulative number of collisions.

Msg Tx Errors

Cumulative number of transmit errors.

Msg Rx Errors

Cumulative number of receive errors.

Tx Retry

Cumulative number of transmit errors.

Originator IP Address

The IP address of the network node making this connection.

Time out Multiplier

The value here specifies the multiplier applied to the expected packet rate (API) to obtain the value used by 
the inactivity timer for this connection.

O2T_RPI

Originator to Target (ie, PLC to SI-EN3) Requested Packet Interval for I/O messaging, in milliseconds, for 
this connection.

O2T_API

Originator to Target (ie, PLC to SI-EN3) Actual Packet Interval for I/O messaging, in milliseconds, for this 
connection.

Consume Msg Cnt

Number of I/O messages consumed (ie, received) from the SI-EN3 since the connection was established or 
statistics were reset for this connection.

T20_RPI

Target to Originator (ie, SI-EN3 to PLC) Requested Packet Interval for I/O messaging, in milliseconds, for 
this connection.

T20_API

Target to Originator (ie, SI-EN3 to PLC) Actual Packet Interval for I/O messages, in milliseconds, for this 
connection.

Produce Msg Cnt

Number of IO messages produced (ie, transmit) from the SI-EN3 since the connection was established or 
statistics were reset for this connection.

Reset Statistics Connection1

Clicking this resets the Consume Msg Cnt and the Produce Msg Cnt for this connection to start counting 
from zero.

EtherNet_conditional_E.book  59 ページ  ２０１６年６月２８日　火曜日　午後１１時３０分

Summary of Contents for SI-EN3






































































Reviews:

No comments